Вісник № 36
Постійне посилання зібрання
Переглянути
Нові надходження
Документ Development of a modular research car ingenio as a platform for analysis of future drive systems(НТУ "ХПІ", 2013) Acker, Michael; Czarnetzki, Walter Theodor; Krawiec, Johannes; Schneider, WaldemarThe paper describes the research projects on electric and hybrid vehicles drivetrain. INGENIO is a new modular test vehicle for research of processes in the powertrain elements. The drivetrain contains self-made fuel cell stack and an invertible electrolyser at the rear frame with fuel cell range extender. The detailed analysis of physical processes in the membrane of fuel cell is given.Документ Integration sicherer antriebsfunktionen nach norm IEC 62061(НТУ "ХПІ", 2013) Kayser, Karl-HeinzThe paper deals with implementation of safety regulations in electric drives. The basic criteria concerning technical systems safety required by IEC 62061 standard are outlined. It is shown how to apply these criteria relative to electric drive operation. Recommendations concerning technical implementation of safety functions in the hardware of electric drives’ control systems are given.Документ Определение параметров термодинамической модели асинхронного двигателя для повторно-кратковременного режима работы(НТУ "ХПИ", 2013) Зюзев, Анатолий Михайлович; Метельков, Владимир ПавловичDiscloses a method of calculation of the thermal conductivity of two-mass thermodynamic model of an induction motor for intermittent operation mode based on the use of heating curves of the stator winding during the working period of the cycle. The results of the simulation are shown.Документ Синтез системы управления фильтрокомпенсирующим устройством на базе регулятора нечеткой логики в составе автономной электроэнергетической системы, часть 2(НТУ "ХПИ", 2013) Жук, А. К.; Запальский, Владимир Николаевич; Запальский, Константин НиколаевичIn the work view complex system regulation power filter, which consist of from the fuzzy - logic regulator and PID - regulator. The result of analyses and synthesis system regulation is characteristic that determination characters of work proposition of control system. The resulting is modeling analysis of control system define necessary criterions of quality control.Документ Модель функціонального діагностування енергоефективності асинхронного електропривода(НТУ "ХПІ", 2013) Закладний, Олег Олександрович; Закладний, Олександр Миколайович; Чермалих, Валентин МихайловичIn this article described the model of functional diagnostics of energy efficiency, energy consumption and energy use processes of the asynchronous electric drive, and the results of analytical test model for induction motors, new industrial series 5A.Документ Оценка статической точности электропривода при предельном демпфировании упругих механических колебаний(НТУ "ХПИ", 2013) Задорожний, Николай Алексеевич; Задорожняя, Инна НиколаевнаIn the article the problem of evaluating the static accuracy of the regulation of speed during the guarantee of active damping of elastic mechanical fluctuations is considered. It is proposed to produce the estimation of the static accuracy of regulation according to a static drop in the speed of electrical drive with the rise of nominal load for the case of the selection of the parameters with the maximum degree of damping of elastic mechanical fluctuations.Документ Особенности работы механизма подачи глубокорасточного станка КЖ-1910 в режиме низких скоростей(НТУ "ХПИ", 2013) Задорожний, Николай Алексеевич; Задорожняя, Инна Николаевна; Ребедак, Олег АлександровичThe processes occurring in the feed mechanism cutter deep-boring machine KJ-1910. Shows the waveform of the linear feed rate cutting tool. Established the fundamental cause of the oscillation feed rate - the presence of elasticity of the kinematic characteristics of the transmission when the nonlinearity of friction.Документ Пуск асинхронних двигунів в умовах енергогенеруючої установки на базі асинхронного генератора з ємнісним збудженням(НТУ "ХПІ", 2013) Зачепа, Юрій Володимирович; Родькін, Дмитро ЙосиповичВ роботі розглядається система регульованого пуску асинхронного двигуна в умовах автономної системи електроживлення на базі асинхронного генератора з ємнісним збудженням. Отримано умови реалізації, розроблено алгоритм та запропоноване технічне рішення щодо пристрою для впровадження режиму «сприятливої» комутації при підключенні споживачів до затискачів автономного асинхронного генератора.Документ Идентификация электрических параметров торцевых ошиновок печей сопротивления прямого действия(НТУ "ХПИ", 2013) Ярымбаш, Дмитрий Сергеевич; Олейников, Александр Михайлович; Ярымбаш, Сергей Тимофеевич; Килимник, Ирина МихайловнаThe upgrade of identification procedure of the electrical parameters of the front bus packages of AC graphitization furnaces using the numerical field analysis and 3D mathematical models of electromagnetic and electrothermal processes are proposed. The around contact resistance boundary subdomain are added. The variation of the finite element density are increased the computational efficiency and calculation accuracy. The face bus packages construction modernization are substantiated. The energy and mass efficiency parameters are improved.Документ Система питания бортовой сети для модернизации тепловозов 2ТЭ10М(НТУ "ХПИ", 2013) Яровой, Геннадий Иванович; Лемешко, Сергей Михайлович; Шамардина, Вера НиколаевнаСистема питания бортовой сети для модернизации тепловозов 2ТЭ10М.Документ Определение начального углового положения ротора синхронного генератора в бездатчиковой системе инверторного запуска дизель-агрегата(НТУ "ХПИ", 2013) Яровой, Геннадий Иванович; Канунников, Р. В.; Анищенко, Николай ВасильевичОпределение начального углового положения ротора синхронного генератора в бездатчиковой системе инверторного запуска дизель-агрегата.Документ Моделирование процессов компенсации реактивной мощности в системе электроснабжения асинхронного двигателя(НТУ "ХПИ", 2013) Ягуп, Валерий Григорьевич; Ягуп, Екатерина ВалериевнаРассматривается система электроснабжения асинхронного двигателя с короткозамкнутым ротором. Компенсация реактивной мощности в системе электроснабжения осуществляется при помощи косинусных конденсаторов. С использо- ванием SPS-модели и метода Нелдера-Мида реализован поиск оптимальных условий компенсации реактивной мощности при заданных условиях работы асинхронного двигателя.Документ Регулятор с двойным интегрированием(НТУ "ХПИ", 2013) Войтенко, Владимир АндреевичThe problem of influencing of negative internal feed-back on electromotive force of engine of direct current on the process of adjusting of current in the contour of adjusting of the current adjusted on a module optimum is examined. It is suggested in place of proportionally-integral regulator of current to use a proportionally-integral regulator with double integration of signal of error on a current.The comparative static and dynamic error of work of contour of current analysis with both regulators is conducted.Документ Скользящие режимы дробных порядков(НТУ "ХПИ", 2013) Волянский, Роман Сергеевич; Садовой, Александр ВалентиновичThe analysis of the control algorithms that provide the formation of the sliding mode of the first and second order is given. Fractional Derivative of amplitude control action is found and analyzed. The conditions of occurrence of the sliding mode of fractional order is shown.Документ Електромеханічна система автоматизації фрезерного верстата(НТУ "ХПІ", 2013) Водічев, Володимир Анатолійович; Алдаїрі, Алі Юсеф Нажаха; Бабійчук, Ольга БорисівнаThe paper is devoted the improvement of the electromechanical system of stabilizing of cutting power of milling machine by development of simple from the point of view technical realization regulator, which provides high exactness of regulation in static operation modes and good value of transients in the conditions of change of object gain. The structure of the system is described and the results of its research on a model are presented.Документ Проблематика взаимосвязанной электромеханической системы станка при скоростной металлообработке(НТУ "ХПИ", 2013) Внуков, Юрий Николаевич; Пирожок, Андрей ВладимировичThe analysis of causes of the regenerating vibration at intensive metal-cutting mode under the influence of vibration trace on transient surface was made. It was found its physical meaning, reasons and regularity. For suppression the self-vibration processes and improving quality at high-speed metal cutting it was introduced the usage of the adaptive speed control system for main drive spindle.Документ Особенности управления электроприводами транспортных средств с электромеханической трансмиссией(НТУ "ХПИ", 2013) Виноградов, Анатолий Брониславович; Гнездов, Николай Евгеньевич; Глебов, Николай АлексеевичDiscusses the problems associated with the development of asynchronous electromotor control systems in complete traction electric equipment sets for vehicles with electromechanical transmission on the example of the concern "Ruselprom" works. The main results of the use of electric drives in vehicles are presented.Документ Энергетическая эффективность асинхронных мотор-генераторов транспортных средств с электромеханической трансмиссией(НТУ "ХПИ", 2013) Виноградов, Анатолий Брониславович; Родионов, Роман Вячеславович; Колосов, Павел Андреевич; Флоренцев, Станислав НиколаевичIn the report experimental researches of power indicators of electromechanical transmissions are resulted. Operating modes of asynchronous erators are investigated. Recommendations for designing of motor-generators of electromechanical transmissions are resulted.Документ Повышение точности прецизионного планарного электропривода(НТУ "ХПИ", 2013) Тяпкин, М. Г.Планарный электропривод получил широкое применение в устройствах, требующих высокой точности и скорости перемещения в плоскости XY. Повышение точности планарного электропривода является перспективной задачей в связи с ростом точностных требований микроэлектронной промышленности. Двухуровневая калибровка планарного электропривода позволяет при минимальных размерах калибровочных таблиц повысить точность электропривода более чем в 3 раза до уровня ±2.5 мкм.Документ Концепция привода электромобиля(НТУ "ХПИ", 2013) Тверд, Михаил; Залески, Ярослав; Дадана, Михаил; Млодзиковски, Павел; Копчак, Любомир Стефанович; Копчак, Богдан ЛюбомировичElectric vehicle drive concept suggests using a single inverter that controls the synchronous permanent magnet motor, and whose shaft is connected to the transmission and a differential. An algorithm for inverter control, based on the principle of maintaining the highest possible flow at the lowest current consumption has been proposed. Such a vehicle can be implemented in a conventional vehicle body, and used for transporting of small shipments necessitating tough and reliable electric drive that works with high efficiency at low speeds.