Розробка узагальненої математичної моделі статичної похибки електромеханічних засобів вимірювальної техніки

Ескіз

Дата

2021

DOI

doi.org/10.20998/2522-9052.2021.2.06

item.page.thesis.degree.name

item.page.thesis.degree.level

item.page.thesis.degree.discipline

item.page.thesis.degree.department

item.page.thesis.degree.grantor

item.page.thesis.degree.advisor

item.page.thesis.degree.committeeMember

Назва журналу

Номер ISSN

Назва тому

Видавець

Національний технічний університет "Харківський політехнічний інститут"

Анотація

Метою статті є подальший розвиток теорії оцінки статичних похибок електромеханічних засобів вимірювальної техніки (ЕмЗВТ) для ефективного їх застосування під час МОб ВТ та контролі функціонування перед застосуванням. Для цього необхідно послідовне вирішення низки теоретичних і прикладних питань, головним з яких є розробка узагальненої математичної моделі статичної похибки ЕмЗВТ, а потім з подальшим її використанням конкретної оцінки статичних похибок для різних структурних схем побудови ЕмЗВТ. Результати. В статті розглядаються прикладні аспекти оцінки статичної похибки електромеханічних засобів вимірювальної техніки визначену через чутливість або статичні коефіцієнти передачі вимірювальних перетворювачів. За результатами аналізу отримана узагальнена математична модель відносної статичної похибки ЕмЗВТ для структурних схем з’єднання вимірювальних перетворювачів (ВП). Висновки. Підтверджено за результатами аналізу, можливість застосування узагаль-неної математичної моделі для оцінки відносної статичної похибки ЕмЗВТ побудованих за різними структурними схемами при їх експлуатації. Використання уточненої статичної похибки надає можливість уточнювати калібрувальну характеристику електромеханічних засобів вимірювальної техніки, що в свою чергу призведе до отримання достовірної інформації про стан військової техніки під час проведення метрологічного обслуговування та безпосередньо при застосуванні.
To keep military equipment fit for use, carry out maintenance activities, an important and integral part of which is metrological service. The effectiveness of metrological services depends on the completeness of the coverage of the monitored parameters, frequency and reliability of their measuring control. The most common, at present, when controlling the parameters of military equipment are electromechanical measuring equipment. The main metrological characteristic of electro-mechanical measuring instruments in a static measurement mode is the nominal calibration characteristic. During operation, the calibration characteristic of electromechanical measuring instruments, under the influence of various factors, has deviations from the nominal, which leads to an instrumental static error. The article deals with the applied aspects of assessing the static error of electromechanical measuring equipment, which is expressed through the sensitivity or static transmission coefficients of measuring transducers. Based on the results of the analysis, a generalized mathematical model of the relative static error of electrome-chanical measuring equipment for various structural schemes of connecting measuring transducers was obtained. It is proposed to apply a generalized mathematical model to assess the relative static error of electromechanical measuring instruments (with various structural schemes) during their operation. The use of an updated static error will allow to refine the calibration characteristics of electromechanical measuring instruments, which in turn will lead to obtaining reliable information about the state of military equipment during metrological maintenance and immediately before use.

Опис

Ключові слова

вимірювальний перетворювач, статична похибка, градуювальна характеристика, measuring transducer, static error, calibration characteristic

Бібліографічний опис

Мошаренков В. В. Розробка узагальненої математичної моделі статичної похибки електромеханічних засобів вимірювальної техніки / В. В. Мошаренков, С. С. Войтенко // Сучасні інформаційні системи = Advanced Information Systems. – 2021. – Т. 5, № 2. – С. 38-41.

item.page.endorsement

item.page.review

item.page.supplemented

item.page.referenced