Кафедра "Матеріалознавство"

Постійне посилання колекціїhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/6927

Офіційний сайт кафедри http://web.kpi.kharkov.ua/mtrlvd

Від 2007 року кафедра має назву "Матеріалознавство", первісна назва – "Металознавство та термічна обробка металів".

Кафедра "Металознавство та термічна обробка металів" створена у 1932 році. Першим її очільником став доктор технічних наук, професор Олександр Володимирович Терещенко.

Кафедра являє собою одну із найстаріших в політехнічному інституті з підготовки інженерів-технологів-дослідників. Своїми науковими дослідженнями. з початку своєї діяльності, кафедра сприяла розвитку та удосконаленню технологій термічної та хіміко-термічної обробки деталей на підприємствах України».

Кафедра входить до складу Навчально-наукового інституту механічної інженерії і транспорту Національного технічного університету "Харківський політехнічний інститут".

У складі науково-педагогічного колективу кафедри працюють: 1 доктор технічних наук, 9 кандидатів технічних наук, 3 кандидата фізико-математичних наук, 1 доктор філософії; 1 співробітник має звання професора, 8 – доцента, 1 – старшого наукового співробітника.

Переглянути

Зараз показуємо 1 - 20 з 289

Changes in the structural state and properties of vacuum-arc coatings based on high-entropy alloy TiZrHfNbTa under the influence of nitrogen pressure and bias potential at deposition
(2018) Sobol, O. V.; Andreev, A. A.; Mygushchenko, R. P.; Gorban, V. F.; Stolbovoy, V. A.; Meylekhov, A. A.; Subbotina, V. V.; Kovteba, D. V.; Zvyagolsky, A. V.; Vuets, A. E.
Complex studies have been carried out on the effect of nitrogen pressure and the negative bias potential on the structure and properties of vacuum-arc nitride coatings based on the high-entropy alloy TiZrHfNbTa. It is defined that the change in pressure during deposition (in the range 0.01...4 mTorr) mainly affects the nitrogen atoms content in the coating. The feed of a negative bias potential to the substrate (Ub = -50...-250 V) makes it possible to control the content of the metallic component using the effect of selective sputtering of atoms in the formation of coatings. Determined, that as the pressure increases the structural state associated with the predominant growth orientation (axial texture) of the crystallites changes. The texture changes in the sequence [311] → [311] + [111] → [111] with increasing pressure for a six-element (TiZrHfVNbTa)N nitride and the texture state changes in the sequence [110] → [110] + [111] → [111] for a five-element (TiZrHfNbTa)N nitride. It is shown that the presence of a bi-textured state in the coating makes it possible to achieve an ultrahard state with a hardness exceeding 50 GPa.
Design of experiments of PVD coatings tin
(Сумський державний університет, 2024) Pinchuk, N. V.
The Effect of Constant and High Voltage Pulse Bias Potentials on the Structure and Properties of Vacuum-Arc (TiVZrNbHf)Nₓ Coatings
(Sumy State University, 2018) Sobol, O. V.; Postelnyk, A. A.; Mygushchenko, R. P.; Gorban, V. F.; Stolbovoy, V. A.; Zvyagolskiy, A. V.
The effect of constant (Ub) and high voltage pulse (Uip) bias potentials supplied to the substrate during condensation, on the structure and properties of vacuum-arc (TiVZrN-Hf)Nх coatings has been studied. It has been determined that the number and size of the drop phase decreases with increasing Ub. The use of Uip promotes a more uniform growth in the coating volume. It is shown that due to the increase of Ub from 0 to 200 V in nitride coatings of high entropy alloys, it is possible to change the growth texture [100] to [111]. This results in increased hardness from 32 GPa to 49 GPa. The supply of high voltage potential in a pulse form leads to a relative decrease in the average size of crystallites and the formation of a bi-texture state. Conditions and mechanisms of the preferential crystallites orientation (axial texture) of vacuum arc (TiVZrNbHf)Nх coatings and texture influence on mechanical properties have been discussed.
Effect of electrolysis regimes on the structure and properties of coatings on aluminum alloys formed by anode-cathode microarc oxidation
(Технологічний центр, 2018) Belozerov, V.; Sobol, O.; Mahatilova, A.; Subbotina, V.; Tabaza, Taha A.; Al-Qawabah, Safwan M.; Al-Qawabeha, Ubeidulla F.
Наведено результати дослідження фазового складу і властивостей МДО-покриттів на алюмінієвих сплавах. Покриття були одержані в лужно-селікатному електроліті на змінному сінусоідальному струмі і в імпульсному режимі струму. Показано, що підвищена щільність мікророзрядів при імпульсної технології збільшує сумарну енергію, що виділяється в них. Це обумовлює підвищення швидкості зростання оксидного покриття і ймовірність утворення α-Al₂O₃ фази. Одержані при мікроплазмове оксидуванні в імпульсному струмовому режимі покриття мають високу твердість і електричну міцність
The effect of the substrate potential during deposition on the structure and properties of the binanolayer multiperiod composites (TiAlSi)N/MeN (Me – Zr, Nb, Cr, Mo)
(2018) Sobol, O. V.; Andreev, A. A.; Mygushchenko, R. P.; Stolbovoy, V. A.; Postelnyk, A. A.; Meylekhov, A. A.; Dolomanov, A. V.; Rebrova, Ye. M.
It is proposed to use the multiperiod binanolayer composites (TiAlSi)N/MeN (Me-Zr, Nb, Cr, Mo) for controlling the structure, stress state and mechanical properties of a multi-element nitride (TiAlSi)N. The deposition of the layers was carried out by the method of vacuum-arc evaporation at different bias potentials on the substrate Ub = -110 and -200 V. It has been determined that mononitrides with a high Me-N binding energy in the binanolayer composite determine the crystallite growth in thin (nanometer) layers. The growth texture is formed in composites containing mononitrides based on transition metals with a relatively small atomic mass (Cr, Mo) at Ub = -110 V. The growth texture is formed at a larger Ub = -200 V when dealing with mononitride based on heavy metal (Zr). The greatest hardness is achieved in textured materials deposited at Ub = -200 V. This is typical both for a monolayer multi-element nitride (TiAlSi)N (hardness is 42.5 GPa) and for multiperiod nanolayer composites based on it (the highest hardness is 47.9 GPa for a composite (TiAlSi)N/ZrN).
The effects of nitrogen atmosphere pressure, constant and high-voltage pulse potentials of the substrate on the structure and properties of vacuum-arc ZrN coatings
(Национальный научный центр "Харьковский физико-технический институт", 2015) Sobol’, O. V.; Andreev, A. A.; Stolbovoy, V. A.; Gorban’, V. F.; Pinchuk, N. V.; Meylekhov, A. A.
ZrN-phase coatings with a cubic lattice (NaCl structure type) were produced by the method of vacuum-arc evaporation of a Zr cathode in nitrogen atmosphere at pressures PN between 0.02 and 0.64 Pa. The pressure increase at a bias potential of -150 V leads to formation of the growth texture [111] or to appearance of the bitextural state with the axes [111] and [311]. Additional pulsed-mode supply of high-voltage negative potential Uip = 800…2000 V, with pulse duration of 10 μs and frequency of 7 kHz, stimulates the emergence of texture [110]. At the substructure level, the Uip supply causes the microstrain relaxation and the crystallite size growth with increasing pressure. The observed changes are attributed to increased particle mobility and nitride formation activity under the action of Uip. The hardness increases with increasing pressure and reaches a value of 43 GPa. The Uip supply leads to a shift of the maximum hardness towards higher pressures.
Formation of Biphasic State in Vacuum-Arc Coatings Obtained by Evaporation of Ti-Al-Zr-Nb-Y Alloy in the Atmosphere of Nitrogen
(Сумской государственный университет, 2014) Beresnev, V. M.; Sobol, O. V.; Toryanik, I. N.; Meylekhov, A. A.; Nyemchenko, U. S.; Turbin, P. V.; Yakushchenko, I. V.; Lisovenko, M. O.
By means of X-ray diffraction, transmission and scanning electron microscopy, energy dispersive spectroscopy and indentation methods, the effect of nitrogen atmosphere pressure on composition, structure and hardness of vacuum-arc (Ti-Al-Zr-Nb-Y)N coatings during the deposition process has been studied. The two-phase state of the coating with solid-solution metal component (bcc lattice) and nitride phase (fcc lattice) have been formed. Increasing the pressure of nitrogen atmosphere leads to the increase of nitrogen component in the coating as well as to increase of the ordering regions size, allowing to achieve the hardness of H = 49 GPa at a pressure of P = 0.5 Pa.
Formation of Superhard State of the TiZrHfNbTaYN Vacuum–Arc High-Entropy Coating
(Allerton Press, Inc., 2018) Beresnev, V. M.; Sobol, O. V.; Andreev, A. A.; Gorban, V. F.; Klimenko, S. A.; Litovchenko, S. V.; Kovteba, D. V.; Meilekhov, A. A.; Postelnyk, A. A.; Nemchenko, U. S.; Novikov, V. Yu.; Maziilin, B. A.
Complex studies of the formation of the superhard state in the TiZrHfNbTaYN vacuum-arc high-entropy coating were carried out. Based on the approach of the structural surface engineering, the regularities of the formation of the triads composition–structure–physico-mechanical properties depending on the supplied potential displacement are established. It is shown that the increase of Ub at the formation of a coating leads to a decrease of the relative content of a light (Ti) and increase of a heavy (Ta, Hf) metal components, which is determined by radiationally stimulated processes in a near surface region at the deposition. The formation of the single-phase state (based on the fcc of metal lattice) in the range Ubfrom –50 to –250 V and revealed the formation of the preferred orientation of the crystallites with the axis [111], which is perpendicular to the growth plane. The increase of the perfection of the texture with the [111] axis with increasing Ub is accompanied with an increase of the coatings hardness, which makes it possible to achieve the superhard state (H = 40.2 GPa) at Ub = –250 V.
Influence of Bias Potential Magnitude on Structural Engineering of ZrN-Based Vacuum-Arc Coatings
(Vasyl Stefanyk Precarpathian National University, 2021) Sobol, O. V.; Postelnyk, H. O.; Pinchuk, N. V.; Meylekhov, A. A.; Zhadko, M. A.; Andreev, A. A.; Stolbovoy, V. A.
The creation of the scientific foundations for the structural engineering of ultrathin nanolayers in multilayer nanocomposites is the basis of modern technologies for the formation of materials with unique functional properties. It is shown that an increase in the negative bias potential (from -70 to -220 V) during the formation of vacuum-arc nanocomposites based on ZrN makes it possible not only to control the preferred orientation of crystallites and substructural characteristics, but also changes the conditions for conjugation of crystal lattices in ultrafine (about 8 nm) nanolayers.
Influence of electrical parameters of the micro-arc oxidation mode on the structure and properties of coatings
(Institute for Single Crystals, 2022) Subbotina, V.; Bilozerov, V.; Subbotin, O.; Barmin, O.; Hryhorieva, S.; Pysarska, N. V.
The influence of different power sources of the micro-arc oxidation process on the peculiarities of structure formation and properties of coatings on aluminum alloy AB formed in alkali-silicate electrolyte in the anode-cathode mode is investigated. It is shown that the pulse technology and the anode-cathode mode make it possible to form coatings containing mainly oxides of the α-Al₂O₃ type (corundum) with a high growth rate. It has been established that with a small thickness of the oxide layer, the rate of heat removal both to the metal and to the electrolyte is high; this fact promotes the formation of alumina in the form of the γ-Al₂O₃ phase. The energy concentration in the thick oxidizing layer causes the formation of high-temperature modification of α-Al₂O₃. It is shown that the mechanism of α-Al₂O₃ formation is determined by two factors: the energy difference in the formation of γ-Al₂O₃ and α-Al₂O₃ phases, and the polymorphic high-temperature transformation of γ-Al₂O₃→α-Al₂O₃ in the high-temperature region of the arc discharge.
The Influence of Layer Thickness and Deposition Conditions on Structural State of NbN/Cu Multilayer Coatings
(Sumy State University, 2019) Sobol, O. V.; Andreev, A. A.; Meylekhov, A. A.; Postelnyk, A. A.; Stolbovoy, V. A.; Ryshchenko, I. M.; Sagaidashnikov, Yu. Ye.; Kraievska, Zh. V.
The influence of the main physical and technological factors of structural engineering (layer thickness, nitrogen atmosphere pressure and bias potential) on the structural-phase state of the NbN/Cu coatings was studied. It was established that with an increase in the thickness of niobium nitride layers from 8 to 40 nm (in the NbN/Cu multilayer composition), the phase composition changes from the metastable NbN (cubic crystal lattice, NaCl structural type) to the equilibrium ε-NbN phase with a hexagonal crystal lattice. At low pressure PN = 7·10 – 4 Torr in thin layers (about 8 nm thick), regardless of the Ub, the NbN phase is formed. The reason for the stabilization of this phase can be the uniformity of the metallic fcc crystal lattice of the δ-NbN phase with the Cu crystal lattice. As the pressure increases from РN = 7·10 – 4 Torr to 3·10 – 3 Torr, a more equilibrium ε-NbN phase with a hexagonal crystal lattice is formed. An increase in the bias potential during deposition from – 50 V to – 200 V mainly affects the change in the preferred orientation of crystallite growth. In thin layers of the NbN phase (about 8 nm), a crystallite texture with the [100] axis is formed. In layers with a thickness of 40-120 nm, crystallites of the NbN phase are predominantly formed with a hexagonal (004) plane parallel to the growth plane. At the greatest layer thickness (more than 250 nm), the NbN phase crystallites are predominantly formed with a (110) hexagonal lattice plane parallel to the growth plane. The results obtained show great potential for structural engineering in niobium nitride when it is used as a constituent layer of the NbN/Cu multilayer periodic system.
The Influence of Layers Thickness on the Structure and Properties of Bilayer Multiperiod Coatings Based on Chromium Nitride and Nitrides of Transition Metals Ti and Mo
(Sumy State University, 2018) Sobol, O. V.; Meylekhov, A. A.; Mygushchenko, R. P.; Postelnyk, A. A.; Tabaza, Taha A.; Al- Qawabah, Safwan M.; Gorban, V. F.; Stolbovoy, V. A.
The influence of the layers thickness of bilayer multi-period coatings of the CrNx/MoNx and CrNx/TiNx systems on their phase-structural state, substructure, stress-strain state and mechanical properties was studied using methods of precision structural analysis in combination with computer simulation of implantation processes during particle deposition. It is established that a two-phase structure of CrN and-Mo2N phases of the structural type NaCl is formed in the multi-period coatings of the CrNx/MoNx system with a nanometer thickness of the layers. Because of the small difference in periods (less than 0.5 %) for Λ = 20 nm, the layers form a coherent interlayer interface. The use of small Ub – 20 V during deposition makes it possible to avoid significant mixing at interlayer (interphase) boundaries even at the smallest Λ = 10 nm. Nitride layers formed under conditions of vacuum arc deposition are under the action of compressive stresses. In the СrNх/TiNх system, because of the relatively large discrepancy between periods (more than 2.5 %), during the formation of the same structural components in the layers (CrN and TiN phases of the structural type NaCl), the epitaxial growth with period adjusting does not occur, even for the smallest Λ = 10 nm. The action of the deformation factor at the interphase boundary allows achieving an ultrahard state (with a hardness of about 50 GPa), which causes a relatively low friction coefficient. The obtained results on the formation of phase-structural states with the nanoscale thickness of layers of multi-period nitride coatings are explained from the position of minimization of surface energy and deformation energy.
Influence of pressure of working atmosphere on the formation of phase-structural state and physical and mechanical properties of vacuum-arc multilayer coatings ZrN/CrN
(2016) Sobol, O. V.; Andreev, A. A.; Gorban, V. F.; Stolbovoy, V. A.; Meylekhov, A. A.; Postelnyk, A. A.; Dolomanov, A. V.
For multilayer coating system ZrN/CrN determined the effect of the pressure of the working atmosphere of nitrogen (Pɴ), DC (˗Us) and pulse (-Ui) negative bias potential during the deposition and the thickness of the layers in the period on the phase composition, texture, substructural characteristics and physical-mechanical properties. It is found that for Рɴ = (2.2...12)·10-4 Torr in the layers of chromium nitride formed on a lower nitrogen phase with the β-Cr2N simple hexagonal crystal lattice, and in the zirconium nitride layers are formed of a stoichiometric ZrN phase with a cubic lattice. Such a multilayer coating (layer thickness about 50 nm) at the maximum in this range Pɴ = 1.2·10-3 Torr is most solid (39 GPa) with a modulus of elasticity of 268 GPa and the ratio H/E = 0.145. At higher Pɴ, when the layers are formed phase stoichiometric composition with homogeneous crystal lattices (ZrN and СrN) hardness of the composition is not more than 33 GPa. The mechanisms of the effects observed are based on the higher barrier properties of the interphase boundary layers with different types of crystal lattices was discussed.
Influence of the Bias Potential and the Pressure of the Nitrogen Atmosphere on the Structure and Properties of Vacuum-arc Coatings Based on the AlCrTiZrNbV High-entropy Alloy
(Sumy State University, 2018) Sobol, O. V.; Andreev, A. A.; Gorban, V. F.; Postelnyk, A. A.; Stolbovoy, V. A.; Zvyagolskiy, A. V.
The effect of the constant bias potential (Ub) supplied to the substrate upon condensation and pressure of the nitrogen atmosphere (PN) on the elemental composition, growth morphology, texture, and physical-mechanical characteristics of vacuum-arc (AlCrTiVZrNb)Nx coatings is studied. It is established that with increasing Ub from – 110V to – 200V, the axis of preferential growth of crystallites of the fcc phase from [100] to [110] changes. Such a change is accompanied by a decrease in the hardness (H) and the ratio H/E (where E is the modulus of elasticity). The conditions for the formation of the preferential orientation of the crystallites (axial texture) of vacuum-arc (AlCrTiVZrNb)Nx coatings and the influence of texture on mechanical properties are discussed. It was established that the change in PN in the range Torr basically allows to vary the degree of filling of the coating with nitrogen atoms. Based on the revealed regularities, the conditions for achieving high hardness for vacuum-arc coatings of nitrides AlCrTiVZrNb high-entropy alloy are substantiated. Because of the presence in the alloy of elements with a relatively low heat of nitride formation, in order to achieve high hardness, it is necessary to use deposition conditions with relatively low energy of bombarding atoms. The use of a low Ub = –110 V at the highest pressure Torr allows achieving an superhard state with a hardness of 44 GPa.
The influence of the conditions of microplasma processing (microarc oxidation in anode-cathode regime) of aluminum alloys on their phase composition
(Технологічний центр, 2017) Belozerov, V.; Sobol, O.; Mahatilova, A.; Subbotina, V.; Tabaza, Taha A.; Al-Qawabeha, Ubeidulla F.; Al-Qawabah, Safwan M.
Наведено дослідження щодо впливу режимів мікроплазмового оксидування в активованих додатками електролітах на фазово-структурний стан покриттів, що формуються на основі алюмінію. Виявлено багато-стадийность фазоутворення в процесі формування покриттів на алюмінієвих сплавах в лужно-силікатном електроліті i анодно-катодному режимі мікроплазмового оксидування. Показано вплив кристаллохімічних характеристик катіонів оброблюваного сплаву і катіонів, що входять до складу електроліту, на процес перетворення γ-Al₂O₃→α-Al₂O₃.
Influence of the magnitude of the bias potential and thickness of the layers on the structure, substructure, stress-deformed state and mechanical (TiMo)N/(TiSi)N coatingsl characteristics of vacuum-arc multi-layered
(2020) Sobol, O. V.; Postelnyk, H. O.; Meylekhov, A. A.; Subbotina, V. V.; Stolbovoy, V. A.; Dolomanov, A. V.; Kolesnikov, D. A.; Kovaleva, M. G.; Sukhorukova, Yu. V.
Layers based on titanium nitride doped with molybdenum and silicon were used to create a multilayer composite. In this case, the mismatch between the lattice periods of (TiMo)N and (TiSi)N layers was about 1%. It was found that in the (TiMo)N/(TiSi)N multilayer composite, such a mismatch of the periods in the constituent layers does not change the single-phase state of the composite even at relatively large layer thicknesses (about 350 nm). The creation of a (TiMo)N/(TiSi)N composite with a nanometer layer thickness allows one to reduce the magnitude of macrostresses (a large value of which is characteristic of single-layer (TiMo)N coatings) and change the substructural characteristics in a wide range of values. It has been established that the use of multi-element (TiMo)N and (TiSi)N layers in a multilayer coating design allows one to achieve a high-hard state with high adhesive strength and good tribological characteristics. The highest properties (hardness – 34.8 GPa and adhesive strength 166.09 N) were achieved in coatings obtained at Ub = -200 V and a layer thickness of 80 nm, which are characterized by compression macrostresses of 7.85 GPa and microstrains 0.75%.
Influence of the thermal factor on the composition of electron-beam high-entropy ALTiVCrNbMo coatings
(Технологический центр, 2018) Sobol, O. V.; Barmin, A. E.; Hryhorieva, S. V.; Gorban, V. F.; Vuets, A. E.; Subbotin, A. V.
This paper reports results of studying the element and phase compositions of electron-beam coatings based on the high-entropy alloy AlTiVCrNbMo, depending on the deposition temperature (in the range of 300...700 °С). The high-entropy alloys were melted in an arc furnace in an atmosphere of high-purity argon. Vacuum condensates of the high-entropy alloy (AlTiVCrNbMo) with a thickness of 3–5 µm were obtained in the vacuum setup UVN-2M-1 at a working vacuum of 5·10-5 mТоrr. The alloy evaporation was performed from the water-cooled ingot mold using an electron-beam gun with a power of 5 kW. Condensation of vapors of all the elements of the alloy was performed onto copper substrates at temperatures of 300, 500, 700 °C. Based on analysis of the element composition of materials of the target made of the high-entropy six-element alloy AlTiVCrNbMo and electron-beam coatings, based on it, we established the critical parameter (specific heat of vaporization of an element) that defined a selective change in the element composition. In accordance with a characteristic change in the composition of coatings of the multi-element high-entropy alloy, 3 groups of elements were distinguished: with a specific heat of evaporation of 280...350 kJ/mol (group 1), 420…460 kJ/mol (group 2), and 590…680 kJ/mol (group 3). It was shown that the formation of a single-phase coating of the high-entropy alloy (based on BCC of the crystalline lattice) occurs at the higher deposition temperature of 500...700 °C when the coating consists of not less than 5 elements. It was established that based on the conditions for an electron-beam process of materials formation, the results obtained can be divided into two types: those determined by the condition of evaporation of the target and those determined by the conditions of coating deposition. The density of flows of elements, evaporated from the target, is determined by their specific heat of evaporation. However, the ratio of atoms in the flow, derived in this way, may not be retained in the formed coating due to the secondary evaporation of elements from the growth surface. The obtained results allow us to substantiate principles for the selection of components for achieving the optimal element and phase compositions of high-entropy alloys.
Investigation of the influence of technological conditions of microarc oxidation of magnesium alloys on their structural state and mechanical properties
(Технологічний центр, 2017) Belozerov, V.; Mahatilova, A.; Sobol, O.; Subbotina, V.; Subbotin, A.
Наведені дослідження структури і властивостей покриттів, отриманих при мікродуговій обробці на магнієвому сплаві. Обробка проводилася при анодно-катодному режимі в лужному електроліті з різними домішками. Показана можливість формування кристалічних оксидних покриттів різного фазового складу (MgO, MgAl₂O₄, Mg₂Sі₄, Mg₃(PO₄)₂) товщиною до 300 мкм, що мають високу адгезію з основою, гарні захисні властивості і високу твердість, яка досягає 6,6 ГПа.
Minimization of errors in discrete wavelet filtering of signals during ultrasonic measurements and testing
(Національний науковий центр "Інститут метрології", 2021) Taranenko, Yu.; Mygushchenko, R. P.; Kropachek, O. Yu.; Suchkov, G. M.; Plesnetsov, Yu.
Error minimizing methods for discrete wavelet filtering of ultrasonic meter signals are considered. For this purpose, special model signals containing various measuring pulses are generated. The psi function of the Daubechies 28 wavelet is used to generate the pulses. Noise is added to the generated pulses. A comparative analysis of the two filtering algorithms is performed. The first algorithm is to limit the amount of detail of the wavelet decomposition coefficients in relation to signal interference. The minimum value of the root mean square error of wavelet decomposition signal deviation which is restored at each level from the initial signal without noise is determined. The second algorithm uses a separate threshold for each level of wavelet decomposition to limit the magnitude of the detail coefficients that are proportional to the standard deviation. Like in the first algorithm, the task is to determine the level of wavelet decomposition at which the minimum standard error is achieved. A feature of both algorithms is an expanded base of discrete wavelets ‒ families of Biorthogonal, Coiflet, Daubechies, Discrete Meyer, Haar, Reverse Biorthogonal, Symlets (106 in total) and threshold functions garotte, garrote, greater, hard, less, soft (6 in total). The model function uses random variables in both algorithms, so the averaging base is used to obtain stable results. Given features of algorithm construction allowed to reveal efficiency of ultrasonic signal filtering on the first algorithm presented in the form of oscilloscopic images. The use of a separate threshold for limiting the number of detail coefficients for each level of discrete wavelet decomposition using the given wavelet base and threshold functions has reduced the filtering error.
Mixing on the Boundaries of Layers of Multilayer Nanoperiod Coatings of the TiNх/ZrNх System: Simulation and Experiment
(Sumy State University, 2017) Sobol, O. V.; Meylekhov, A. A.; Mygushchenko, R. P.; Postelnyk, A. A.; Sagaidashnikov, Yu. Ye.; Stolbovoy, V. A.
Using the complex of methods for attestation of the structural state in combination with computer simulation and measurement of mechanical properties (hardness), the influence of the period Λ on the mixing process on the interlayer boundaries of multilayer coatings TiNх/ZrNх is studied. The formation of two phases (TiN and ZrN) with one type of crystal lattice (structural type NaCl) is identified in the layers of multiperiodic compositions TiNx/ZrNx with a period of Λ = 20 ... 300 nm. At Λ = 10 nm, the formation of a solid solution (Zr, Ti)N, as well as a small volume of the TiN phase is revealed on XRD spectras. The presence of TiN component is due to the larger initial value of the layer based on titanium nitride. To explain the results obtained, the results of computer simulation of damage at the atomic level during bombardment by ions accelerated in the Ub field are used. The critical thickness of mixing (about 7 nm) in the TiNx/ZrNx system is determined upon condition that Ub = – 110 V. It is established that a decrease in the period from 300 to 20 nm leads to increase in hardness. The highest hardness of 44.8 GPa corresponds to the superhard state. It is established that the critical thickness of radiation-stimulated defect formation has a significant effect on the stress-strain state and hardness of coatings with a small Λ ≈ 10 nm. In this case, relaxation of the stress-strain compression state occurs and the hardness decreases. However, the formation of a solid solution, while retaining part of the unreacted layer of titanium nitride at Λ = 10 nm, makes it possible to obtain an ultrahigh (44.8 GPa) hardness of the coating.