2023 № 5 Електротехніка і Електромеханіка
Постійне посилання колекціїhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/68537
Переглянути
2 результатів
Результати пошуку
Документ Experimental evaluation of conducted disturbances induced during high frequency switching of active components(Національний технічний університет "Харківський політехнічний інститут", 2023) Slimani, Helima; Zeghoudi, Abdelhakim; Bendaoud, Abdelber; Bechekir, SeyfeddinePower electronics devices are among the most widely used equipment in all fields. The increasing performance of these devices makes their electromagnetic interference factor very important. On the other hand, electromagnetic compatibility research is more and more interested in studies on the sources of electromagnetic disturbances, their propagation paths and the methods of reducing these electromagnetic disturbances. The purpose is to study the behavior of the various active power components at high frequency as well as the evaluation of their electromagnetic noise by using simulation and experimental measurement. Methods. In first time, the simulation was realized with the Lt-spice software which presents many advantages in its use and we validate in the second time the results obtained with experimental measurements. We start by study of the behavior of the diode, then the behavior of MOSFET transistor and finally the study of the behavior of the IGBT transistor. Results. All the simulations were performed using the Lt-spice software and the results obtained are validated by experimental measurements performed in the APELEC Laboratory at the University of Sidi Bel-Abbes in Algeria. The waveforms of the current and voltage across each component during its opening are presented. The results of the simulations are compared and validated with the realized measurements in order to better present the influence of the fast switching of semiconductors on the electrical quantities, which causes electromagnetic disturbances in the interconnected electrical system.Документ Development of a boost-inverter converter under electromagnetic compatibility stress equipping a photovoltaic generator(Національний технічний університет "Харківський політехнічний інститут", 2023) Bechekir, Seyfeddine; Zeghoudi, Abdelhakim; Ould-Abdeslam, Djaffar; Brahami, Mostefa; Slimani, Helima; Bendaoud, AbdelberIntroduction. Static converters are among the most widely used equipment in several applications, for example, electric power transmission, motor speed variation, photovoltaic panels, which constitute the electronic components. The design of a power electronics device is done without any real means of predicting electromagnetic disturbances during the product development phase. This case-by-case development process is repeated until a solution is found that best respects all the electromagnetic compatibility constraints. The purpose is the development of a boost-inverter converter under electromagnetic compatibility constraints. The improvements made to the inverter are mainly in the control, the choice of power switches and the electromagnetic compatibility solutions brought to the device. The quality of the wave is improved by acting on the type of control and the choice of switches. Methods. In the first time, we have highlighted a comparison between two most frequently used power components (MOSFET and IGBT) in the inverter and the boost by simulation using ISIS and LT-spice softwares. The sinusoidal voltage with modulation circuit is greatly simplified by the use of the PIC16F876A microcontroller. In a second step, we validate the obtained results with experimental measurements. We start with the boost, then the inverter. In addition, the circuits made are housed in boxes to avoid accidental contact for people. The equipment is designed to isolate the load from the power supply in case of: over voltages, under voltages, high and low battery level and short circuits. Results. All the simulations were performed using the ISIS and LT-spice softwares. The obtained results are validated by experimental measurements performed in the ICEPS Laboratory at the University of Sidi Bel-Abbes in Algeria. The realization of a single-phase inverter with a pulse width modulation control, associated with a boost chopper and the waveforms of the current and voltage across each static converter its opening are presented. The sources of disturbances in power devices are at the origin of the temporal and frequency characteristics of the signals coming from the hot spots of the power switches and the resonances created during the switching of these elements.