Видання НТУ "ХПІ"
Постійне посилання на розділhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/62886
Переглянути
2 результатів
Результати пошуку
Документ A high-frequency modeling of AC motor in a frequency range from 40 Hz to 110 MHz(Національний технічний університет "Харківський політехнічний інститут", 2022) Miloudi, Houcine; Miloudi, Mohamed; Gourbi, Abdelkader; Bermaki, Mohammed Hamza; Bendaoud, Abdelber; Zeghoudi, AbdelhakimMost electromagnetic compatibility models developed for the study of three-phase induction machines are generally valid for low and medium frequencies (<< 1 MHz). This frequency limit seems to be too restrictive for the overall study of conducted electromagnetic interference. In this paper, the model is using the proposed model and compared with experimental results in low and medium frequency. And then, the high-frequency modeling of induction motor is presented new method based on transfer function model. The proposed methodology is verified on an experimental and simulation, it’s suitable for prediction of the terminal overvoltage analysis and electromagnetic interference problems and common-mode and differential-mode currents. The novelty of the work consists to develop an improved high-frequency motor model based on transfer function to represent the motor high-frequency behavior for frequency-domain analyses in the frequency range from 40 Hz up to 110 MHz .The purpose of this work is to study the common-mode impedance and the differential-mode impedance of AC motor. The determination of these impedances is done for firstly both common and differential modes at low and medium frequency, and then common-mode and differential-mode characteristics at high frequency. Methods. For the study of the path of common-mode and differential-mode currents in typical AC motor (0.25 kW, 50 Hz) an identification method in high frequency for induction motor has been proposed based on the transfer function in differential-mode and common-mode configuration. The low and medium frequency model were presented in the first time based on equivalent circuit of electrical motor. Then, the common-mode and differential-mode impedances were defined in high frequency using asymptotic approach. This motor was studied by MATLAB Software for simulation and also experimental measurements. Results. All the simulations were performed using the mathematical model and the results obtained are validated by experimental measurements performed in the University of the Federal Armed Forces Hamburg in Germany. The obtained results of common-mode and differential-mode at low frequency, medium and high frequency are compared between simulation and experiment.Документ Measurement and analysis of common and differential modes conducted emissions generated by an AC/DC converter(Національний технічний університет "Харківський політехнічний інститут", 2022) Zeghoudi, Abdelhakim ; Slimani, Helima; Bendaoud, Abdelber; Benazza, Baghdadi ; Bechekir, Seyfeddine; Miloudi, HoucineRectifiers are the most important converters in a very wide field: the transport of electrical energy in direct current and in the applications of direct current motors. In most electrical and electronic systems, rectifiers are non-linear loads made up of diodes, therefore they are a source of harmonic pollution at a base frequency with a distorting line current signal that generates electromagnetic interference. There are two disturbance modes: common mode and differential mode. These disturbances caused by the rapid variation of current and voltage as a function of time due to the switching of active components, passive components such as inductors, capacitors, coupling, etc. The purpose of this work is to study the conducted emissions generated by a rectifier connected to the Line Impedance Stabilizing Network in an electric circuit. The determination of these disturbances is done for firstly both common and differential modes at high frequency, and secondly harmonics current, line current at low frequency. The novelty of the proposed work consists in presenting a study of disturbance generated by rectifiers using simulation and also experimental measurements at low and high frequencies in order to compare the results. Methods. For the study of the disturbances conducted by the diode bridge converter (rectifier), the sources of conducted electromagnetic disturbances were presented in the first time. Then, the common and differential modes were defined. This converter was studied by LTspice Software for simulation and also experimental measurements at low frequency for harmonics current and high frequencies for disturbances in common and differential modes. Results. All the simulations were performed using the LTspice software and the results obtained are validated by experimental measurements performed in the APELEC laboratory at the University of Sidi Bel-Abbes in Algeria. The obtained results of conducted emissions at high frequency and total harmonics distortion of current at low frequency are compared between simulation and experiment.