Військовий інститут танкових військ НТУ "ХПІ"

Постійне посилання на розділhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/21691

Начальник інституту
Серпухов Олександр Васильович
Склад інституту
1. Факультет озброєння і військової техніки;
2. Факультет радіаційного, хімічного, біологічного захисту та екологічної безпеки;
3. Кафедра фізичного виховання спеціальної фізичної підготовки і спорту;
4. Кафедра військової підготовки офіцерів запасу;
5. Батальйон забезпечення навчального процесу.

Переглянути

Результати пошуку

Зараз показуємо 1 - 5 з 5

Electroplating and functional properties of Fe-Mo and Fe-Mo-W coatings
(Украинский государственный химико-технологический университет, 2014) Ved, M. V.; Sakhnenko, N. D.; Karakurkchi, A. V.; Yermolenko, I. Yu.
Peculiarities of electrodeposition Fe-Mo and Fe-Mo-W coatings from citrate bath containing iron (III) on substrates of mild steel and cast iron are investigated. The utilization of iron (III) compounds significantly enhanced the stability and service life of electrolyte due to elimination redox reactions involving complexing and side anodic reactions. The effect of alloying components salt concentration and electrolysis mode on the quality, composition and properties of the alloys were determined. It is shown that alloys formed in nonstationary electrolysis have a uniform surface, composition and a lower content of impurities. Increased physical and mechanical properties as well as corrosion resistance of Fe-Mo and Fe-Mo-W coatings compared with the base metal are caused by the presence of propensity for passivation alloying components as well as by amorphous structure of electroplating alloys. Indicated coatings can be considered as promising in surface hardening technologies and repair of of worn items.
Electrochemical deposition of Fe–Mo–W alloy coatings from citrate electrolyte
(Allerton Press, 2016) Karakurkchi, A. V.; Ved, M. V.; Yermolenko, I. Yu.; Sakhnenko, N. D.
Peculiarities of the electrochemical deposition of Fe–Mo–W coatings from citrate electrolyte containing iron (III) on the substrates of mild steel and gray cast iron are investigated. The effect of the salt concentration of alloying components and electrolysis modes on the quality, composition, and properties of the alloys is determined. It is shown that the alloys formed via nonstationary electrolysis exhibit a more uniform surface and lower content of impurities. The improved physical and mechanical properties as well as corrosion resistance of Fe–Mo–W coatings in comparison with the base metal can be considered as promising technologies for surface hardening and repair of worn items.
Electrodeposition of iron-molybdenum-tungsten coatings from citrate electrolytes
(Pleiades Publishing, 2015) Karakurkchi, A. V.; Ved, M. V.; Sakhnenko, N. D.; Yermolenko, I. Yu.
Specific features of the electrodeposition of iron–molybdenum–tungsten coatings from citrate electrolytes based on iron(III) sulfate in the dc mode and with a unipolar pulsed current were studied. It was shown that varying the relative concentrations of salts of alloy-forming metals and the solution pH makes it possible to obtain lustrous compact coatings with low porosity and various contents of high-melting components. The effect of temperature on the coating composition and current efficiency was examined. The current density ranges providing high electrolysis efficiency were found and it was demonstrated that using a pulsed current favors formation of more compositionally homogeneous surface layers at a smaller amount of adsorbed nonmetallic impurities in the coatings. The iron–molybdenum–tungsten coatings are X-ray-amorphous and have better physicomechanical properties and corrosion resistance as compared with the base, which makes it possible to recommend these coatings for application in techniques for surface reinforcement and restoration of worn-out articles.
Functional properties of multicomponent galvanic alloys of iron with molybdenum and tungsten
(Institute for Single Crystals, 2015) Karakurkchi, A. V.; Ved, M. V.; Sakhnenko, N. D.; Yermolenko, I. Yu.; Zyubanova, S. I.; Kolupayeva, Z. I.
Galvanic alloy coatings Fe-Mo (W) and Fe-Mo-W were deposited from citrate bath based on Fe (III) using both direct and pulsed current on substrates steel 3 and grey cast iron GC 18. It was shown that the alloying components content, their distribution on the surface, morphology and topography of the coatings are depended on the electrolysis mode. It was established that the functional properties of the binary and ternary alloys of iron (corrosion resistance, microhardness, antifriction et al.) exceed parameters of the substrate and are predetermined by the composition, structure, material and surface roughness.
Iron binary and ternary coatings with molybdenum and tungsten
(Elsevier Inc., 2016) Ved, M.; Sakhnenko, N. D.; Karakurkchi, A.; Yermolenko, I. Yu.; Yar-Mukhamedova, G.
Electrodeposition of Fe-Mo-W and Fe-Mo layers from a citrate solution containing iron(III) on steel and iron substrates is compared. The utilization of iron(III) compounds significantly improved the electrolyte stability eliminating side anodic redox reactions. The influence of concentration ratios and electrodeposition mode on quality, chemical composition, and functional properties of the alloys is determined. It has been found that alloys deposited in pulse mode have more uniform surface morphology and chemical composition and contain less impurities. Improvement in physical and mechanical properties as well as corrosion resistance of Fe-Mo and Fe-Mo-W deposits when compared with main alloy forming metals is driven by alloying components chemical passivity as well as by alloys amorphous structure. Indicated deposits can be considered promising materials in surface hardening technologies and repair of worn out items.