Технологія обробки гвинтової поверхні роз'ємного з'єднання в деталях з армованих композиційних матеріалів

dc.contributor.authorДовгополов, Андрій Юрійовичuk
dc.contributor.authorНекрасов, Сергій Сергійовичuk
dc.date.accessioned2017-01-30T11:56:41Z
dc.date.available2017-01-30T11:56:41Z
dc.date.issued2016
dc.description.abstractЗ метою дослідження можливості утворення якісно нового роз’ємного з’єднання для деталей з армованих композиційних матеріалів, була розроблена, на основі раніше відомого методу технологія виготовлення подібного роз’ємного з’єднання [4]. З урахуванням всіх рекомендацій для даного типу матеріалів [1] створена геометрія інструменту, та визначеніумови оброки підібране обладнання та приладдя дляреалізаціїприведеної технології обробки.uk
dc.description.abstractWith a research objective of a possibility of creation of qualitatively new detachable joint for details from the reinforced composite materials, the manufacturing techniques of a similar detachable joint were developed on the basis of earlier known method [4]. Taking into account all recommendations for this type of materials [1] the tool geometry is created, and processing conditions are defined the equipment and accessories to realization of the given technology of processing is picked up. The recommended geometrical parameters of the cutting tool for processing of the reinforced composite materials the following: front corner у =20-30 °, rear corner a=10-15 °, point corner P = 50-60 °. The mode is realized on multiple-purpose the equipment, without use of the additional equipment and devices. Taking into account all recommendations it was also succeeded to develop new technology for a detachable joint in the reinforced composite materials. The purpose of work was development of manufacturing techniques of the offered detachable joint for the details made of the reinforced composite materials. Methods of the decision is an adaptation of earlier known mode to our conditions of processing, it very well turned out. As a result of the done work everything very well managed to be reached all objectives.en
dc.identifier.citationДовгополов А. Ю. Технологія обробки гвинтової поверхні роз'ємного з'єднання в деталях з армованих композиційних матеріалів / А. Ю. Довгополов, С. С. Некрасов // Вісник Нац. техн. ун-ту "ХПІ" : зб. наук. пр. Сер. : Нові рішення в сучасних технологіях = Bulletin of National Technical University "KhPI" : coll. of sci. papers. Ser. : New solutions in modern technologies. – Харків : НТУ "ХПІ", 2016. – № 42 (1214). – С. 38-42.uk
dc.identifier.urihttps://repository.kpi.kharkov.ua/handle/KhPI-Press/26749
dc.language.isouk
dc.publisherНТУ "ХПІ"uk
dc.subjectвуглепластик􀀪􀀝􀀫􀀭􀀳􀀣􀀭􀀟􀀠􀀩􀀦 􀀱􀀑 􀀩􀀟􀀑 􀀠􀀱􀀭􀀬􀀣􀀭􀀟􀀠􀀩􀀦􀀱􀀼􀀑uk
dc.subjectсклопластикuk
dc.subjectкругла різьбаuk
dc.subjectфрезеруванняuk
dc.subjectтехнологія виготовленняuk
dc.subjectreinforced composite materialsen
dc.subjectplug contacten
dc.subjectmanufacturing technologyen
dc.subjectmillingen
dc.titleТехнологія обробки гвинтової поверхні роз'ємного з'єднання в деталях з армованих композиційних матеріалівuk
dc.title.alternativeTechnology of processing of a crew surface of a detachable joint in details from the rainforced composite materialsen
dc.typeArticleen

Файли

Контейнер файлів

Зараз показуємо 1 - 1 з 1
Ескіз
Назва:
vestnik_KhPI_2016_42_Dovhopolov_Tekhnolohiia.pdf
Розмір:
371.38 KB
Формат:
Adobe Portable Document Format

Ліцензійна угода

Зараз показуємо 1 - 1 з 1
Ескіз недоступний
Назва:
license.txt
Розмір:
11.21 KB
Формат:
Item-specific license agreed upon to submission
Опис:

Колекції