Формирование выхлопного отсека перспективного ЦНД с рабочей лопаткой 1650 мм
Вантажиться...
Дата
2018
DOI
10.20998/2078-774X.2018.12.01
Науковий ступінь
Рівень дисертації
Шифр та назва спеціальності
Рада захисту
Установа захисту
Науковий керівник
Члени комітету
Видавець
НТУ "ХПИ"
Анотація
Рассмотрены результаты расчетно-конструкторских разработок и численных исследований проточной части выхлопного отсека цилиндра низкого давления (ЦНД) в составе последней ступени с рабочей лопаткой 1650 мм с отсосом влагоемкого пара из межвенцового зазора, канала предвкюченного межступенчатого зазора с отбором пара, выхлопного патрубка с учетом установки системы охлаждения и переходного патрубка. Представлены некоторые методические аспекты и сравнительные результаты исследований на основе численного эксперимента.
The results of computational design and numerical studies of the low-pressure cylinder exhaust chamber flow path with the last stage with a 1650 mm length blade are considered. The flow path of stage contained a suction of a moisture-intensive vapor from the interrow gap, a channel of the predetermined interstage gap with steam extraction, an exhaust pipe, taking into account the installation of the system cooling and transition nozzle. All the computations were based on the model of one speed wet steam flow without droplets and super cooling was not taken into account. The sectorial approach was applied to description of the interaction of the last stage and exhaust hood. The stages were considered in steady state formulation. The initial data and boundary conditions were taken basing on results of flow simulation of whole L.P.C flow path [1, 2]. Some methodological aspects and the directions of improving of studied facilities in numerical experiment by MTFS® code are discussed.
The results of computational design and numerical studies of the low-pressure cylinder exhaust chamber flow path with the last stage with a 1650 mm length blade are considered. The flow path of stage contained a suction of a moisture-intensive vapor from the interrow gap, a channel of the predetermined interstage gap with steam extraction, an exhaust pipe, taking into account the installation of the system cooling and transition nozzle. All the computations were based on the model of one speed wet steam flow without droplets and super cooling was not taken into account. The sectorial approach was applied to description of the interaction of the last stage and exhaust hood. The stages were considered in steady state formulation. The initial data and boundary conditions were taken basing on results of flow simulation of whole L.P.C flow path [1, 2]. Some methodological aspects and the directions of improving of studied facilities in numerical experiment by MTFS® code are discussed.
Опис
Ключові слова
цилиндр низкого давления, выхлопной отсек, диффузор, ступени, утечки пара, проточная часть, потери кинетической энергии, неравномерность давления, численная модель, low-pressure cylinder, exhaust compartment, flow path, stages, diffuser, steam leakage, flow section, kinetic energy loss, pressure nonuniformity, numerical model
Бібліографічний опис
Солодов В. Г. Формирование выхлопного отсека перспективного ЦНД с рабочей лопаткой 1650 мм / В. Г. Солодов, В. А. Конев // Вісник Нац. техн. ун-ту "ХПІ" : зб. наук. пр. Сер. : Енергетичні та теплотехнічні процеси й устаткування = Bulletin of the National Technical University "KhPI" : coll. sci. papers. Ser. : Power and Heat Engineering Processes and Equipment. – Харків : НТУ "ХПІ", 2018. – № 12 (1288). – С. 4-10.