2021 № 94 Різання та інструменти в технологічних системах
Постійне посилання колекціїhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/77628
Переглянути
16 результатів
Результати пошуку
Документ Technological provision of the accuracy for the thread form of rod pumps(Національний технічний університет "Харківський політехнічний інститут", 2021) Yakovenko, Igor; Vasilevskyi, Yu.; Basova, Yevheniia; Edl, MilanAspects of thread manufacturing used in downhole rod pumps are considered. Technological defects of distortion of lateral surfaces of a thread profile arising in the course of processing on CNC machines are described, and the factors which most influence formation of these defects are established. The influence of profile defects on the reliability of the threaded connection during the operation of rod pumps is analyzed, as well as the research on the dynamics and oscillations of machine systems is analyzed. With the performed analysis the mathematical model of real techn ological system in the course of machining process is created and investigated. The main technological factors that have the greatest influence on the occurrence of error in the shape of the thread surface are identified. With the help of software for analysis of dynamic systems, the necessarily calculations were performed and the behavior of the dynamic system in the process of forming the thread profile was considered. Based on the analysis of the obtained results, a system for managing the parameters of the technological process of threading and technological solutions formulated. The introduction of which had a positive impact on the stability of the machining process and reduce the frequency of the above defect.Документ Influence of the geometric characteristics of the discontinuous profile working surfaces of abrasive wheels for precision and temperature when grinding(Національний технічний університет "Харківський політехнічний інститут", 2021) Yakimov, A.; Bovnegra, L.; Tonkonogyi, V.; Vaysman, V. O.; Strelbitskyi, V.; Sinko, I.Grinding is the most common finishing method for hardened steel parts. Grinding is accompanied by a large heat release in the cutting area, under the influence of which structural changes appear in the thin surface of the processed parts, tensile stress and even microcracks, which significantly reduce the operational reliability of machines that include these parts. The use of abrasive wheels with an intermittent working surface makes it possible to reduce the temperature in the area of contact of abrasive grains with the material of the workpiece and, as a consequence, stabilize the quality of the surface layer of the workpieces. High-frequency vibrations in the elastic system of the machine, accompanying the work of an intermittent wheel, are a positive factor that reduces the energy consumption of the grinding process. However, under certain conditions of dynamic interaction of the tool with the workpiece, parametric resonance may occur, which worsens the geometric and physical-mechanical parameters of the quality of the surface layer of the processed part. The aim of the work is to realize the possibility of predicting the quality parameters of the surface layer of parts during intermittent grinding by studying the influence of the design features of the macrotopography of the working surface of abrasive wheels and processing modes on the nature of the dynamic interaction of the tool with the workpiece and the heat stress in the cutting area. It was found that the parametric vibrations of the elastic system of the machine tool can be shifted to a more stable area, due to an increase in the number of interruptions of the working surface of the abrasive whee l with a constant ratio of the length of the protrusions and depressions. The increase in the number of breaks on the wheel also contributes to a decrease in temperature in the cutting area. It was found that to maintain the stable operation of the elastic system of the machine, it is necessary to reduce the number of cavities on the grinding wheel with an increase in the cutting speed. However, both of these actions are accompanied by an increase in the heat stress of the grinding process. It has been experimentally established that for ordinary (pendulum) grinding, it is possible to achieve an increase in processing productivity by increasing the speed of the longitudinal movement of the table.Документ The importants of clustering in logistic systems(Національний технічний університет "Харківський політехнічний інститут", 2021) Veres, P.Nowadays, the development of higher efficient processes and procedures is the key for success in industrial environment. The companies have machines, production lines, software and hardware tools with high level principles of efficient working. Example: the Industry 4.0 concept use the machines and methods of the near past, upgrade them, and gave them new purpose, as a more efficient tool. Some of the bases of those tools are not as efficient as which many would think, like in group generating or in other word clustering. Clustering is a very hard process, and it is in almost every decision making in every company’s lives. It is important to sometimes examine its significance and flaws. This paper presents the clustering briefly and shows its errors through an example.Документ Automatic control of temperature and power conditions during rough grinding of slabs(Національний технічний університет "Харківський політехнічний інститут", 2021) Tihenko, V.; Lebedev, V. V.; Chumachenko, T.The production of high-quality rolled products (slabs), the formation of its surface phase-structural composition, texture, stress state during rough grinding depends on the temperature in the area of contact between the wheel and the slab. During processing, due to geometric errors of the rolled surface, as well as due to local changes in hardness, periodic fluctuations of the instantaneous depth of cut occur, which can be determined indirectly by controlling one of the technological parameters, for example, the power spent on grinding, with subsequent recalculation it to online temperature values. The grinding temperature is described as a control object in the form of an aperiodic link. Computer simulation has confirmed the efficiency of the system for maintaining the specified temperature of slab grinding under various operating conditions that simulate the situations of real production.Документ The effect of the circular feed on the surface roughness and the machining time(Національний технічний університет "Харківський політехнічний інститут", 2021) Sztankovics, IstvánThe surface roughness is analysed in different feeds and turning procedures (rotational and conventional) in this paper. Cutting experiments were made on different cutting speeds and feed rates with 2 cutting tool with helical edge geometry and 1 traditional turning tool. The measured 2D surface roughness values were compared between the different cutting tools. The benefit of the circular feed application is showed by the decrease of roughness parameters and machining time.Документ Surface roughness modeling during electric discharge grinding with variable polarity of electrodes(Національний технічний університет "Харківський політехнічний інститут", 2021) Strelchuk, R. M.The article presents the probabilistic-statistical modeling of surface roughness in the process of electric discharge grinding with the variable polarity of electrodes. The correlation between electric modes of machining and indicators of the quality of the machined surface was established. A probabilistic-statistical model of part surface roughness formed during grinding is obtained, which establishes the correlation between high-altitude surface parameters and electrical machining modes. The developed model makes it possible to calculate the height parameters of the part roughness depending on the electrical modes of grinding. The height of microroughness is determined by the same machining conditions as the depth of erosion pits. It is possible to obtain low roughness if electrical machining modes are reduced.Документ Technological fixtures for machining large-sized thin-walled shells of complex profile(Національний технічний університет "Харківський політехнічний інститут", 2021) Oliinyk, S.; Kalafatova, L.The paper analyzes the structure of technological fixtures for the positioning and fixing of large-sized thin-walled pyroceram shells as a factor affecting the dynamic characteristics of the grinding system. The solution to the problem of ensuring the dynamic stability of the «mandrel-workpiece» subsystem is necessary to increase the efficiency of shell machining in present conditions. Studying the vibrations frequency spectrum of the technological system during grinding has made it possible to determine their sources. The magnitude and frequency of vibrations depend on the mandrel structure - the clamping fixture. The study results are the requirements for a new mandrel structure, considering the dynamic stability of the technological system.Документ Investigation of the effect of areal roughness measurement length on face milled surface topographies(Національний технічний університет "Харківський політехнічний інститут", 2021) Nagy, AntalSurface roughness is of great importance in the manufacturing industry, as it affects surfaces’ tribological properties (wear, friction, lubrication, etc.), corrosion resistance, fatigue strength and appearance. Areal roughness measurement, which provides a more comprehensive characterization of surfaces, is becoming increasingly popular, but systematic studies are still lacking, so measurements are often analyzed differently. In this paper, the effect of the measurement length is analyzed in the main measurement direction on areal roughness of face milled surface topographies, which were measured with a confocal chromatic sensor.Документ Tribology and topography of hard machined surfaces(Національний технічний університет "Харківський політехнічний інститут", 2021) Molnar, ViktorIn machining automotive industrial parts by hard machining procedures, the topographic characteristics of high accuracy surfaces have high importance. In this paper 2D and 3D surface roughness features of gear bores machined by hard turning and grinding are demonstrated. The 3D roughness parameters, which are considered as more exact than the 2D parameters, were compared to the 2D ones, which are used more widely in industrial practice. The analyzed machining procedure versions were ranked based on the topographic parameters determining the tribological (wear and oil-retention capability) characteristics of the different surfaces.Документ Interaction of the abrasive medium with the treated surface and the process of metal removal during vibration treatment in the presence of a chemically active solution(Національний технічний університет "Харківський політехнічний інститут", 2021) Fedorovich, V. A.; Grabchenko, A. I.; Mitsyk, A. V.Interaction of working medium granules with the processed surface of the part is considered. It is noted that the processing methods are characterized by the dynamic interact ion of the abrasive medium with the processed surface. It is indicated that during vibration treatment there is an impact contact of the abrasive granule with the surface of the part, which leads to the formation of characteristic traces during the formation of the surface relief. The types of impact of abrasive grains of working medium granules on the surface of the processed part are identified. It is indicated that the effect of abrasive grains depends on the geometric parameters of the tops of the grains and the working contour of the granule as a whole. The alternation of the operation of abrasive grains in the connection with the nature of the motion of the granule over the surface of the part is shown. The interaction of surfaces of bodies during vibration treatment is considered. The distinctive features of the vibration treatment method from other analogs are indicated. The conditions for the formation of the surface layer of the part during vibration processing are given. The analysis of the mechani cal-physicochemical model of the micro-cutting process in the presence of a chemically active solution is carried out and a comparison of the intensity of technologies for vibration treatment of steel parts is given.