Кафедри
Постійне посилання на розділhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/35393
Переглянути
3 результатів
Результати пошуку
Документ Recycling of Polymer Waste into Plastic Lubricants(2022) Grigorov, Andrey; Sinkevich, Irina; Ponomarenko, Natalia; Bondarenko, Oleksandr; Usachov, Dmytro; Matukhno, Vasyl; Shevchuk, OleksandrA technology for the production of greases from polymeric household waste has been proposed, including the stage of boiling the polymer in a solvent, which is used as a used motor oil SAE10W-40. In the production of greases using this technology, a significant amount of used polymer products is utilized, while the share of waste from low-pressure polyethylene and polypropylene (PP) is, respectively, 20-50% of the mass and 50-75% of the mass. This approach makes it possible to significantly expand the raw material base of the specified technological process and, due to the involvement of relatively cheap raw materials, significantly reduce the cost of finished products. The results of the study of the adhesive properties of the obtained lubricants allow us to give the following recommendations: for lubricants based on low-pressure polyethylene with a polymer: oil ratio of 1: 1, the rational rotation speed was no more than 2850 rpm, with a ratio of 1: 3 - about 3950 rpm and with a ratio of 1 : 5 - up to 5300 rpm; rational rotation speed for lubricants based on PP at a polymer: oil ratio of 1: 1 does not exceed 3600 rpm, at a ratio of 2: 1- 4900 rpm and at a ratio of 3: 1 - 6000 rpm.Документ Technology for Producing Components of Technological and Boiler Fuels from Polymer Raw Materials(2021) Shevchenko, Kyrylo; Grigorov, A. B.; Ponomarenko, Vitaliy; Nahliuk, Mikhail; Bondarenko, Oleksandr; Stetsiuk, Yevhen; Matukhno, VasylThe article presents a schematic diagram of obtaining the components of technological and boiler fuels from polymer raw materials represented by materials from low and high pressure polyethylene, polypropylene and polystyrene. This scheme is based on the process of non-catalytic thermal destruction of raw materials in a batch reactor and consists of a section for preparation of raw materials, a section for thermal destruction as well as the fractionation of the resulting products. The given scheme on an industrial scale, depending on the properties of the raw material, makes it possible to obtain 10-20% (mass) of the fraction - 200°C, 30-50% (mass) of the 200-360°C fraction and 20-30% (mass.) fractions (> 360°C). Among the by-products, 3.0-5.0% (mass) light hydrocarbon gases (0.5-1.0 mass %) and the coke residue are formed. According to their properties, the obtained liquid products can be used as components for the production of process and a boiler fuel or as additives to improve the low-temperature properties of commercial fuels.Документ Improvement of Operational Properties of Technological Fuel – A Review(2021) Shevchenko, Kyrylo; Grigorov, A. B.; Neshko, Svetlana; Desna, Natalia; Bondarenko, Oleksandr; Stetsiuk, YevhenAn overview of the ways of improving the operational properties of furnace and boiler fuels has been presented; their positive and negative features have been analyzed. It has been established that the most effective way to improve the operational properties of furnace and boiler fuels is their compounding with additives as well as various components since it is easy to implement under conditions of direct application of process fuel. It has been suggested that a very successful alternative to the additives and components used in industry can be fractions (components) obtained by thermal destruction in the temperature range of 300-380°C of secondary polymer raw materials, represented by polyethylene, polypropylene, and polystyrene.