Кафедри
Постійне посилання на розділhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/35393
Переглянути
7 результатів
Результати пошуку
Документ Establishing rational conditions for obtaining potassium glycerate(PC Тесhnology сеntеr, 2021) Sytnik, Natalia; Kunitsia, Ekaterina; Mazaeva, Viktoria; Chernukha, Anton; Ostapov, Kostiantyn; Borodych, Pavlo; Mazurenko, Valerii; Kovalov, Oleksandr; Velma, Victoria; Kolokolov, VitaliiThis paper reports a study into the dependence of efficient glycerate potassium production involving glycerin and potassium hydroxide solution on the process conditions. The concentration of potassium glycerate in the resulting product has been used as a parameter of the efficient glycerate potassium production process. Glycerates of metals are applied to produce articles in the construction industry, electronics, medicine; they are employed as transesterification catalysts to obtain special fats for various purposes, as well as biodiesel fuel. In order to derive potassium glycerate, heating was applied while agitating a mixture of glycerin and potassium hydroxide. The analysis of potassium hydroxide was performed, in which the basic substance mass fraction was 85.5 %, the mass fraction of carbonate potassium – 0.9 %. The p.a.-grade glycerin was applied in this work, whose basic substance mass fraction was 99.5 %. The effect of the heating temperature of the reaction mixture on the concentration of potassium glycerate in the product has been determined. It has been shown that the rational heating temperature is 145 °C. The dependence of potassium glycerate concentration in the resulting product on the following conditions of the process has been established: a change in the molar concentration of glycerin and a reaction mixture heating duration. Such rational conditions for obtaining potassium glycerate have been defined as a molar concentration of glycerin of 60 % and a heating duration of 4 hours. The experimentally established concentration of potassium glycerate in the product under these conditions was 75.77 %. For potassium glycerate, the melting point (69 °C) and the mass fraction of moisture (0.8 %) have been determined. The results of experimental studies would make it possible to obtain potassium glycerate directly at enterprises where the glycerates of metals are used, from available raw materials, under rational conditions. The defined conditions for obtaining potassium glycerate could make it possible to efficiently utilize material and energy resources.Документ Rational parameters of waxes obtaining from oil winterization waste(PC Тесhnology сеntеr, 2020) Sytnik, Natalia; Kunitsia, Ekaterina; Mazaeva, Viktoria; Chernukha, Anton; Kovalov, Pavlo; Grigorenko, Natalia; Gornostal, Stella; Yermakova, Olena; Pavlunko, Mykola; Kravtsov, MikhailProduction of waxes from spent perlite, which is a waste of sunflower oil winterization, is studied. Winterization is characterized by significant losses of oil with filter powders, and waste utilization is an environmental and economic problem. At the same time, winterization waste contains valuable components – wax and oil, which can be used in different ways. The content of waxes in spent perlite using hexane (18 %), as well as the quality indicators of the obtained wax: melting point 70 °C, saponification number 115 mg KOH/g, acid number 2.6 mg KOH/g, mass fraction of moisture 0,82 % are determined. Spent perlite was treated with a solution of sodium chloride during boiling, settling of the obtained mass, washing and drying of wax. The dependence of the yield and melting point of the extracted waxes on the processing parameters: the concentration of sodium chloride solution, temperature and duration of settling is found. Rational conditions for spent perlite processing are determined: the concentration of sodium chloride solution – 7.5 %, settling temperature – 20 °C, settling duration ‑ 10 hours. The experimentally determined wax yield at this point is 14.3 %. Quality indicators of the wax sample obtained under rational conditions are studied: melting point 68 °С, saponification number 110 mg KOH/g, acid number 2.8 mg KOH/g, mass fraction of moisture 0.85 %. These values correlate with the data for wax extracted using hexane, as well as with reference data on the quality of beeswax and sunflower wax. The data obtained allow recycling spent perlite without organic solvents, which makes the process more environmentally friendly and cost-effective, as well as solves environmental problems associated with the utilization of winterization waste.Документ Implementation of the plasmochemical activation of technological solutions in the process of ecologization of malt production(PC Тесhnology сеntеr, 2020) Kovaliova, Olena; Pivovarov, Olexandr; Kalyna, Viktoriia; Tchoursinov, Yuriy; Kunitsia, Ekaterina; Chernukha, Anton; Polkovnychenko, Dmytro; Grigorenko, Natalia; Kurska, Tetiana; Yermakova, OlenaThis study has established patterns in the plasmochemical activation of technological solutions in the process of malt production. Of importance is the application of innovative technologies to purify water and technological solutions used at malt enterprises that consume large quantities of water resources. A promising technology is the plasmochemical treatment of water and technological solutions in order to purify them and, partially or completely, destroy pathogenic microflora. Due to the use of plasmochemical activation, it has become possible not only to improve the malting process but also to reduce the consumption of water resources for technological purposes by 2‒3 times. This is achieved by improving the technological malting process and by the possibility of reuse of wastewater after its filtering and plasmochemical treatment. The experimental laboratory tests have proven the effectiveness of using plasmochemical activation of technological solutions in order to improve the qualitative indicators of wastewater and the possibility of reuse of such solutions after their plasmochemical activation. Applying the proposed method for treating technological solutions decreased the level of contamination of wastewater from malt production. Sewage contamination after activation decreased. Thus, pollution indicators decreased as follows: per dry residue – by 65‒95 %; the content of suspended substances – by 33‒66 %; residue after roasting – by 58‒79 %; total nitrogen – by 58‒80 %; P2O5 (phosphorus) – by 75‒88 %; K2O (potassium) – by 75‒ 92 %; CaO (calcium) – by 81‒92 %; Na2O – by 67–83 %; Cl- – not detected; oxidation – by 78‒95 %; BOC5 (biochemical oxygen consumption) ‒ by 92‒97 %; pH became alkaline. In plasmochemical treatment, there is a disinfection of wastewater, namely, during an activation mode of 60 min the phytopathogenic microflora (Aspergillus, Alternaria, Penicillium, Fusarium, Mucor) were destroyed. This indicates the effectiveness of the purification and decontamination of technological solutions. Its application is the key to the environmental safety of malt production when all its stages meet the requirements of "green" technologies.Публікація Determination of the influence of natural antioxidant concentrations on the shelf life of sunflower oil(PC Тесhnology сеntеr, 2020) Sytnik, Natalia; Kunitsia, Ekaterina; Mazaeva, Viktoria; Chernukha, Anton; Bezuglov, Oleg; Bogatov, Oleg; Beliuchenko, Dmytr; Maksymov, Andrii; Popov, Mykola; Novik, I. O.The influence of natural antioxidants from different types of vegetable raw materials on the processes of oxidative and hydrolytic spoilage of sunflower oil during storage is studied. Plant antioxidants are more environmentally friendly and safer than synthetic ones. Green tea leaves and oak bark were used as vegetable raw materials. Water-ethanol extracts from vegetable raw materials were added to oil samples in experimental concentrations. The samples were stored in the laboratory conditions at the temperature of (20±2) °C. The study was performed for 5 months. The values of the acid and peroxide numbers were determined. The most effective blend of antioxidants showed the increase in the acid number from 0.12 to 0.20 mg KOH/g (concentration of green tea extract – 0.05 %, without the addition of oak bark extract). According to the values of the peroxide number, the most effective blends of antioxidants were the experiment points with the following green tea extract:oak bark extract ratio: (0.05:0.05) %, (0.025:0.025) %, (0.025:0.05) %, (0.05:0.025) %. To determine the induction period of oil and, accordingly, its shelf life under experimental conditions, the values of the peroxide numbers were used. It is rational to use extractives from oak bark and green tea under the following conditions: the concentration of each of the antioxidant extracts in terms of dry matter – (0.025‑0.04) %. The maximum induction period is 100 days. The efficiency of natural antioxidants in terms of the concentration of oak bark and green tea extracts is 0.05 and 0.025 %, respectively, was compared to the effectiveness of the corresponding concentration of one of the synthetic antioxidants – butylhydroxyanisole. When using butylhydroxyanisole, the induction period of oil was 65 days, and when using natural antioxidants – 74 days.Документ Identification of patterns in the production of a biologically-active component for food products(PC Тесhnology сеntеr, 2020) Kovaliova, Olena; Tchoursinov, Yuriy; Kalyna, Viktoriia; Koshulko, Vitalii; Kunitsia, Ekaterina; Chernukha, Anton; Bezuglov, Oleg; Bogatov, Oleg; Polkovnychenko, Dmytro; Grigorenko, Natalia; Polkovnychenko, DmytroThe study reported here has established patterns in the intensive technology for making a biologically active component (the sprouts of legumes) whose germination involved natural fruit acids (citric, malic, grape). The choice of high-quality and safe stimulants is important for the germination of different grain raw materials. Such substances are the fruit acids of natural origin. Their application has made it possible to obtain a high-value component for healthy foods, namely, the sprouts of a variety of legumes. The experimental research has proven the effectiveness of using fruit acids as the effective intensifiers and disinfectants for the process of obtaining the legume sprouts. It has been shown that their use makes it possible not only to intensify the germination of legumes but also contributes to the more active formation of sprouts, and disinfects the seedbed. Thus, the use of aqueous solutions of fruit acids at the concentration of 0.25–1.25 % led to an increase in the following indicators: the germination energy, by 4–7 %; the ability to germinate, by 5–8 %; the length of the sprouts, by 3–11 mm; the weight of the sprouts, from 1 to 12 % depending on the crop. In addition, the composition of the sprouts has been investigated, which confirmed the biological usefulness and rationality of their introduction to the composition of food products as a biologically active component. The reported study has shown that they contain the elevated content of amino acids (by 3–50 % depending on the amino acid), vitamins(В1, В2, В3, В6, В12, РР, Е, С, А), the high content of protein (32 %) and extractive substances (44 %). This testifies to the biological and nutritional value of the sprouts obtained using intensive technology. The investigated technology for making legumes sprouts is innovative. The sprouts obtained can become highly nutritious components for new health food products.Документ Development of amino acid balanced food systems based on wheat flour and oilseed meal(PC тесhnology сеntеr, 2020) Papchenko, Victoriia; Matveeva, Tatiana; Bochkarev, Sergiy; Belinska, Anna; Kunitsia, Ekaterina; Chernukha, Anton; Bezuglov, Oleg; Bogatov, Oleg; Polkovnychenko, Dmytro; Shcherbak, SergeyThe analysis of the main methods of increasing the nutritional and biological value of wheat flour has been conducted. Considerable attention is paid to the issue of adjusting the protein content in flour due to additives. The relevance of improving the amino acid composition of flour protein is emphasized. The feasibility of comprehensive studies for the development of food system formulations with a balanced amino acid composition based on wheat flour and oilseed meal is substantiated. The amino acid content has been experimentally determined and the biological value of raw materials proteins for food systems which are sunflower and soybean meal has been calculated. The mixture composition of sunflower and soybean meal with an improved amino acid composition has been scientifically substantiated. It has been found that the protein composition of the meal mixture is maximally close to the reference in terms of the content of leucine, lysine and the amount of sulfur-containing amino acids (methionine, cystine). The score of isoleucine, tryptophan, phenylalanine and tyrosine in the protein composition of oilseed meal is 1.1–1.47 times higher than the reference. The amino acid composition has been calculated and the biological value of the protein of food systems containing 80–90 % wheat flour and 10–20 % composition of soybean and sunflower meal with improved amino acid composition has been determined. It has been found that the formulation of the food system containing 20 % of the composition of meal mixture and 80 % of wheat flour has the greatest biological value in comparison with wheat flour. In this food system, the limited amino acids – lysine and sulfur-containing (methionine and cystine) are the closest to the reference one and are 67.68 % and 70.12 %. The fatty acid composition has been experimentally determined. The biological effectiveness of the fats of the developed food systems has been calculated. The closest to the fatty acid ratio recommended by nutritionists is the food system with a ratio of meal mixture: wheat flour of 20:80. The resulting formulations of food systems will be useful in technologies of flour products with high biological value.Документ Processing of ethanol-containing waste of oil neutralization in the technology of hand cleaning paste(PC тесhnology сеntеr, 2021) Petik, Ihor; Belinska, Anna; Kunitsia, Ekaterina; Bochkarev, Sergiy; Ovsiannikova, Tetiana; Kalyna, Viktoriia; Chernukha, Anton; Ostapov, Kostiantyn; Grigorenko, Natalia; Petukhova, OlenaThe graphical dependence of the washing capacity of ethanol-containing soapstock on the concentration in an aqueous solution and the temperature of interaction with the polluted material has been determined. It is proposed to use a 40 % aqueous solution of ethanol-containing soapstock in the hand cleaning paste technology. This soapstock solution has a washing capacity of 92–98 % at the temperature of interaction with the polluted material of 25–40 °C. The regularity of the effect of the structurant content on the consistency of hand cleaning paste was investigated using an approximating polynomial. This made it possible to substantiate the effective concentration of carboxymethyl cellulose (0.4...0.6 %) and cetysltearyl alcohol (1.8...2.0 %) in the formulation. The obtained regression equation is useful for adjusting the content of structurants in the formulation, depending on the consumer's requirements for the viscosity of the developed detergent. A comparison of the quality indicators of the developed hand cleaning paste based on ethanol-containing soapstock with a sample of similar “Primaterra Automotive” commercial hand cleaning paste was carried out. The quality indicators of the developed paste are as follows: effective viscosity at 20...22 °С – 32.0 Pa∙s; foaming capacity – 23 mm, foam stability – 62.0 %; washing ability – 92.0 %. It was determined that these quality indicators do not differ significantly in the developed detergent and commercial analogue. The data obtained indicate the prospects of processing ethanol-containing soapstock into the hand cleaning paste based on natural surfactants. The developed detergent due to the content of ethanol, glycerin and hydrogen peroxide has antiseptic properties, which is a competitive advantage among analogues. Such utilization of ethanol-containing soapstock makes the process of oil neutralization environmentally safe and economically viable.