Кафедри
Постійне посилання на розділhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/35393
Переглянути
7 результатів
Результати пошуку
Документ The Use of Negative Bias Potential for Structural Engineering of Vacuum-Arc Nitride Coatings Based on FeCoNiCuAlCrV High-Entropy Alloy(Sumy State University, 2018) Sobol, O. V.; Andreev, A. A.; Gorban, V. F.; Meylekhov, A. A.; Postelnуk, A. A.; Stolbovoy, V. A.; Zvyagolskiy, A. V.The effect of negative bias potential (Ub = – 40, – 110, and – 200 V) upon the deposition of multielement coatings on their composition, structure, and mechanical properties was studied. It is shown that when using a high-entropy multielement (of 7 elements) FeCoNiCuAlCrV alloy, it is possible to obtain a single-phase nitride (FeCoNiCuAlCrV)N. Nitride has an fcc crystal lattice (structural type NaCl). It has been established that with an increase in Ub in the structural state occurs transition from practically nontextured (polycrystalline) to the preferential orientation of the growth of crystallites with the [111] texture axis (at Ub = – 110 V) and [110] (at Ub = – 200 V). This is accompanied by a decrease in the lattice period, as well as a decrease in hardness and modulus of elasticity. For coatings (FeCoNiCuAlCrV) N, the highest hardness of 38 GPa is achieved by using the smallest (– 40 V) bias potential during the deposition process. It is shown that to achieve high hardness at high Ub it is necessary to increase the content in the highentropy alloy of elements with high nitride-forming ability.Документ Structure and Properties of Vacuum-arc Coatings of Chromium and Its Nitrides Obtained under the Action of Constant and Pulse High-voltage Bias Potential(Sumy State University, 2017) Sobol, O. V.; Postelnyk, A. A.; Mygushchenko, R. P.; Al-Qawabeha, Ubeidulla F.; Tabaza, Taha A.; Al-Qawabah, Safwan M.; Gorban, V. F.; Stolbovoy, V. A.To reveal the regularities of structural engineering of vacuum-arc coatings based on chromium and its nitrides, the influence of the main physicotechnological factors (the pressure of the nitrogen atmosphere and the bias potential) in the formation of coatings was studied. It was discovered that during the deposition of chromium coatings the formation of the texture axis [100], as well as the macrodeformation of compression is happening. The supply of a high-voltage negative pulse potential to the substrate increases the mobility of the deposited atoms and leads to relaxation of the compression deformation. As the pressure increases from Torr, the phase composition of the coatings changes: Cr (JCPDS 06-0694) → Cr2N(JCPDS 35-0803) → CrN(JCPDS 11-0065). The supply of high-voltage pulses leads to the formation of a texture of crystallites with parallel growth surfaces planes having d ≈ 0.14 nm. The structure obtained by pulsed high-voltage action makes it possible to increase the hardness of the coating to 32 GPa and reduce the friction coefficient to 0.32 in the "chromium nitride-steel" system and to 0.11 in the "chromium nitride-diamond" system. The results obtained are explained from the viewpoint of increasing the mobility of atoms and the formation of cascades of displacements when using an additional high-voltage potential in the pulse form during the deposition of chromium-based coatings.Документ Influence of the Bias Potential and the Pressure of the Nitrogen Atmosphere on the Structure and Properties of Vacuum-arc Coatings Based on the AlCrTiZrNbV High-entropy Alloy(Sumy State University, 2018) Sobol, O. V.; Andreev, A. A.; Gorban, V. F.; Postelnyk, A. A.; Stolbovoy, V. A.; Zvyagolskiy, A. V.The effect of the constant bias potential (Ub) supplied to the substrate upon condensation and pressure of the nitrogen atmosphere (PN) on the elemental composition, growth morphology, texture, and physical-mechanical characteristics of vacuum-arc (AlCrTiVZrNb)Nx coatings is studied. It is established that with increasing Ub from – 110V to – 200V, the axis of preferential growth of crystallites of the fcc phase from [100] to [110] changes. Such a change is accompanied by a decrease in the hardness (H) and the ratio H/E (where E is the modulus of elasticity). The conditions for the formation of the preferential orientation of the crystallites (axial texture) of vacuum-arc (AlCrTiVZrNb)Nx coatings and the influence of texture on mechanical properties are discussed. It was established that the change in PN in the range Torr basically allows to vary the degree of filling of the coating with nitrogen atoms. Based on the revealed regularities, the conditions for achieving high hardness for vacuum-arc coatings of nitrides AlCrTiVZrNb high-entropy alloy are substantiated. Because of the presence in the alloy of elements with a relatively low heat of nitride formation, in order to achieve high hardness, it is necessary to use deposition conditions with relatively low energy of bombarding atoms. The use of a low Ub = –110 V at the highest pressure Torr allows achieving an superhard state with a hardness of 44 GPa.Документ The Effect of Constant and High Voltage Pulse Bias Potentials on the Structure and Properties of Vacuum-Arc (TiVZrNbHf)Nₓ Coatings(Sumy State University, 2018) Sobol, O. V.; Postelnyk, A. A.; Mygushchenko, R. P.; Gorban, V. F.; Stolbovoy, V. A.; Zvyagolskiy, A. V.The effect of constant (Ub) and high voltage pulse (Uip) bias potentials supplied to the substrate during condensation, on the structure and properties of vacuum-arc (TiVZrN-Hf)Nх coatings has been studied. It has been determined that the number and size of the drop phase decreases with increasing Ub. The use of Uip promotes a more uniform growth in the coating volume. It is shown that due to the increase of Ub from 0 to 200 V in nitride coatings of high entropy alloys, it is possible to change the growth texture [100] to [111]. This results in increased hardness from 32 GPa to 49 GPa. The supply of high voltage potential in a pulse form leads to a relative decrease in the average size of crystallites and the formation of a bi-texture state. Conditions and mechanisms of the preferential crystallites orientation (axial texture) of vacuum arc (TiVZrNbHf)Nх coatings and texture influence on mechanical properties have been discussed.Документ The Influence of Layers Thickness on the Structure and Properties of Bilayer Multiperiod Coatings Based on Chromium Nitride and Nitrides of Transition Metals Ti and Mo(Sumy State University, 2018) Sobol, O. V.; Meylekhov, A. A.; Mygushchenko, R. P.; Postelnyk, A. A.; Tabaza, Taha A.; Al- Qawabah, Safwan M.; Gorban, V. F.; Stolbovoy, V. A.The influence of the layers thickness of bilayer multi-period coatings of the CrNx/MoNx and CrNx/TiNx systems on their phase-structural state, substructure, stress-strain state and mechanical properties was studied using methods of precision structural analysis in combination with computer simulation of implantation processes during particle deposition. It is established that a two-phase structure of CrN and-Mo2N phases of the structural type NaCl is formed in the multi-period coatings of the CrNx/MoNx system with a nanometer thickness of the layers. Because of the small difference in periods (less than 0.5 %) for Λ = 20 nm, the layers form a coherent interlayer interface. The use of small Ub – 20 V during deposition makes it possible to avoid significant mixing at interlayer (interphase) boundaries even at the smallest Λ = 10 nm. Nitride layers formed under conditions of vacuum arc deposition are under the action of compressive stresses. In the СrNх/TiNх system, because of the relatively large discrepancy between periods (more than 2.5 %), during the formation of the same structural components in the layers (CrN and TiN phases of the structural type NaCl), the epitaxial growth with period adjusting does not occur, even for the smallest Λ = 10 nm. The action of the deformation factor at the interphase boundary allows achieving an ultrahard state (with a hardness of about 50 GPa), which causes a relatively low friction coefficient. The obtained results on the formation of phase-structural states with the nanoscale thickness of layers of multi-period nitride coatings are explained from the position of minimization of surface energy and deformation energy.Документ А Computer Simulation of Radiation-Induced Structural Changes and Properties of Multiperiod ZrNₓ/MoNₓ System(Sumy State University, 2017) Sobol, O. V.; Meylekhov, A. A.; Bochulia, T. V.; Stolbovoy, V. A.; Gorban, V. F.; Postelnyk, A. A.; Shevchenko, S. M.; Yanchev, A. V.Influence of the period value Λ (at different negative potential Ub that supplied during deposition) on phase composition, structure, stress-strain state and hardness of multiperiod coatings ZrNₓ/MoNₓ is investigated by using complex methods of validation structural state at combined with microindentation. Formation in layers ZrNx and MoNx the phases with cubic lattice and preferred orientation of crystallites with axis [100] is established. Stress-strain state of compression with increasing Ub is amplified and reaches maximum value (– 6.7 GPa) at Λ = 20 nm and Ub – 110 V. Hardness of coating increases with decreasing Λ from 300 to 20 nm. Coatings that obtained with Λ = 20 nm and Ub – 110 V have the highest hardness 44 GPa. Relaxation of structural compressive stresses and decreasing hardness is happening at smaller Λ and larger Ub – 110 V (as a result of radiation-stimulated forming defect and mixing). Data of computer modeling of defectiveness at atomic level at bombardment of ions that accelerated in field Ub are used to explain the results.Документ Influence of the thermal factor on the composition of electron-beam high-entropy ALTiVCrNbMo coatings(Технологический центр, 2018) Sobol, O. V.; Barmin, A. E.; Hryhorieva, S. V.; Gorban, V. F.; Vuets, A. E.; Subbotin, A. V.This paper reports results of studying the element and phase compositions of electron-beam coatings based on the high-entropy alloy AlTiVCrNbMo, depending on the deposition temperature (in the range of 300...700 °С). The high-entropy alloys were melted in an arc furnace in an atmosphere of high-purity argon. Vacuum condensates of the high-entropy alloy (AlTiVCrNbMo) with a thickness of 3–5 µm were obtained in the vacuum setup UVN-2M-1 at a working vacuum of 5·10-5 mТоrr. The alloy evaporation was performed from the water-cooled ingot mold using an electron-beam gun with a power of 5 kW. Condensation of vapors of all the elements of the alloy was performed onto copper substrates at temperatures of 300, 500, 700 °C. Based on analysis of the element composition of materials of the target made of the high-entropy six-element alloy AlTiVCrNbMo and electron-beam coatings, based on it, we established the critical parameter (specific heat of vaporization of an element) that defined a selective change in the element composition. In accordance with a characteristic change in the composition of coatings of the multi-element high-entropy alloy, 3 groups of elements were distinguished: with a specific heat of evaporation of 280...350 kJ/mol (group 1), 420…460 kJ/mol (group 2), and 590…680 kJ/mol (group 3). It was shown that the formation of a single-phase coating of the high-entropy alloy (based on BCC of the crystalline lattice) occurs at the higher deposition temperature of 500...700 °C when the coating consists of not less than 5 elements. It was established that based on the conditions for an electron-beam process of materials formation, the results obtained can be divided into two types: those determined by the condition of evaporation of the target and those determined by the conditions of coating deposition. The density of flows of elements, evaporated from the target, is determined by their specific heat of evaporation. However, the ratio of atoms in the flow, derived in this way, may not be retained in the formed coating due to the secondary evaporation of elements from the growth surface. The obtained results allow us to substantiate principles for the selection of components for achieving the optimal element and phase compositions of high-entropy alloys.