Кафедри
Постійне посилання на розділhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/35393
Переглянути
3 результатів
Результати пошуку
Документ Метод визначення адгезійних властивостей пластичних мастил(ТОВ "Планета-Принт", 2020) Григоров, Андрій БорисовичЗапропоновано метод визначення адгезійних властивостей пластичних мастил, заснований на визначенні швидкості обертання ротору лабораторної центрифуги, при якій величина втрати мастила з поверхні металевої пластини, розташованої у гнізді центрифуги, буде дорівнювати 50% від початкової маси.Документ Optimization of floccular cleaning and drainage of thin dispersed sludges(Scientific Route, Estonia, 2020) Shestopalov, Oleksii; Briankin, Oleksandr; Rykusova, Nadegda; Hetta, Oksana S.; Raiko, Valentina; Tseitlin, MusiiThe efficiency of solid phase retention and dehydration of finely dispersed products of a coal processing plant and a metallur gical enterprise on the module for cleaning and dewatering sludge is investigated. A technique for selecting the operating parameters of equipment based on the determination of the strength criterion of flocs is proposed. A methodology for technological tests has been developed to control the flocculation process and optimize the flow of flocculant depending on the concentration of the solid phase. Industrial tests on the module for wastewater treatment and sludge dewatering using flocculants proved the effectiveness of the developed methodology. It is shown that the conditions for conducting tests on flocculation should correspond to the operating conditions of the circuit apparatus for cleaning and dewatering sludge. These conditions include sludge performance, sludge flow rate in the cross section of pipes and apparatuses, and the flow time from the flocculator to the centrifuge. During the testing of the Module, the solids retention efficiency of 97–99 % was achieved with the strength criteria of flocs in front of a centrifuge of 2–2.5 mm/s. The conditions for the high efficiency of the apparatus chain are the optimization of the aggregation process itself. It is revealed that for the formation of strong flocs it is necessary to regulate the concentration of the solid phase. For coal sludge, the concentration of the solid phase before the flocculant is fed must be maintained no higher than 50–60 g/l, and for gas treatment sludge – no higher than 20–25 g/l. Correction of the concentration of sludge before the flocculator is possible by diluting it with clarified water to the optimum concentration for aggregation. It is found that the moisture content of the sediment and the efficiency of the retention of the solid phase depend on the strength criterion of the flocs. Therefore, the optimization of the flocculant flow rate is possible by controlling and the residual floccule deposition rate after mechanical action in front of the dewatering equipment. The flocculant flow rate must be adjusted depending on the concentration of the solid phase in the sludge to achieve the desired criterion for the strength of the flocs.Документ Adhesion properties of recycling greases(2019) Grigorov, Andrey; Sytnik, Alexey; Karchakova, Valeriia; Ponomarenko, Vitaliy; Rudniev, VasylThe results of the study of the adhesion properties of recycling greases expressed in terms of the residual amount of grease that is stored on a metal plate after testing in a laboratory centrifuge are presented. It was established that the investigated samples of recycling greases in the range of the thickness of the deposition layer up to 1.0 mm, by their adhesion properties, are fully suitable for using in all types of bearings operated with a rotation speed of up to 2500 rpm. From the number of investigated grease samples, samples with a deposition layer thickness of 0.1 mm o have evidence of fairly high values of the rotational speed when the threshold value of the residual amount of grease is reached.