Кафедри
Постійне посилання на розділhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/35393
Переглянути
2 результатів
Результати пошуку
Документ Creep pores in welded joints of steam pipelines(Springer Science+Business Media, LLC, 2023) Dmytryk, V. V.; Glushko, A. V.; Poznyakov, V. D.; Kasyanenko, I. V.Formation of creep pores and their transformation into creep cracks in the metal of welded joints of steam pipelines made of heat-resistant pearlite steels (12Kh1MF and 15Kh1M1F), with the long-term operation (over 270,000 h) under creep and low-cycle fatigue conditions (via repeated start-stop modes), largely depends on the structural and phase state of the welded joints. Welded joints are characterized by structural heterogeneity caused by welding heat. The heterogeneity increases with their further service life. This heterogeneity in the metal of welded joints is much greater than the heterogeneity of the base metal of the steam line, which has not been subjected to welding heat. In long-term operation, the structure of steam lines and their welded joints is transformed into a ferritic-carbide mixture at different rates. The rate of this transformation in the metal of welded joints is much higher than in the base metal of steam lines. It was found that the intensity of damage to the metal of welded joints by pores and creep cracks largely depends on the level of transformation of the initial structure into a ferritic-carbide mixture. It was found that creep pores are mainly formed along the boundaries of ߙ-phase grains and, to a lesser extent, along the grain body. We studied the peculiarities of physical and chemical processes occurring in the metal of welded joints of steam pipelines. We established a link between the self-diffusion of alloying elements (chromium, molybdenum, and vanadium) and the movement of dislocations. It was found that pore nucleation in the metal of welded joints occurs mainly at the boundaries of ferrite and bainite grains, where the coagulating carbides M23C6 and M7C3 are located rather than along the grain body. In the process of diffusion movement, vacancies, by merging, are transformed into microcontinuities that move in the direction of vacancy movement. It was found that the formation of creep pores in the metal of welded joints largely depends on its structural and phase state. Creep pores are most intensively formed in areas where the structure consists of tempering bainite, ferrite, and coagulating globularized pearlite. It was found that with an increase in the metal deformation of the zone of thermal influence of welded joints, the formation of creep pores is accelerated.Документ Ползучесть сварных соединений паропроводов(Академпериодика, 2018) Глушко, Алена Валерьевна; Дмитрик, Виталий Владимирович; Сыренко, Т. А.Представлены результаты изучения особенностей изменения структурного состояния металла сварных соединений паропроводов из теплоустойчивых перлитных Cr–Mo–V-сталей, длительно эксплуатируемых в условиях ползучести. Показана роль влияния физико-химических процессов, проходящих в металле сварных соединений паропроводов, на их структурные изменения. Деформация металла сварных соединений, обеспечиваемая перемещением дислокаций, является наибольшей на участке неполной перекристаллизации зоны термического влияния (ЗТВ). Скорость ползучести преимущественно контролируется переползанием дислокаций и зависит от структурного состояния металла сварных соединений. Увеличение деформации металла сварных соединений при их наработке в условиях ползучести до 200000 ч имеет преимущественно линейный характер, а после характер деформации будет отличаться от линейного.