Кафедри
Постійне посилання на розділhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/35393
Переглянути
12 результатів
Результати пошуку
Документ Influence of the Bias Potential and the Pressure of the Nitrogen Atmosphere on the Structure and Properties of Vacuum-arc Coatings Based on the AlCrTiZrNbV High-entropy Alloy(Sumy State University, 2018) Sobol, O. V.; Andreev, A. A.; Gorban, V. F.; Postelnyk, A. A.; Stolbovoy, V. A.; Zvyagolskiy, A. V.The effect of the constant bias potential (Ub) supplied to the substrate upon condensation and pressure of the nitrogen atmosphere (PN) on the elemental composition, growth morphology, texture, and physical-mechanical characteristics of vacuum-arc (AlCrTiVZrNb)Nx coatings is studied. It is established that with increasing Ub from – 110V to – 200V, the axis of preferential growth of crystallites of the fcc phase from [100] to [110] changes. Such a change is accompanied by a decrease in the hardness (H) and the ratio H/E (where E is the modulus of elasticity). The conditions for the formation of the preferential orientation of the crystallites (axial texture) of vacuum-arc (AlCrTiVZrNb)Nx coatings and the influence of texture on mechanical properties are discussed. It was established that the change in PN in the range Torr basically allows to vary the degree of filling of the coating with nitrogen atoms. Based on the revealed regularities, the conditions for achieving high hardness for vacuum-arc coatings of nitrides AlCrTiVZrNb high-entropy alloy are substantiated. Because of the presence in the alloy of elements with a relatively low heat of nitride formation, in order to achieve high hardness, it is necessary to use deposition conditions with relatively low energy of bombarding atoms. The use of a low Ub = –110 V at the highest pressure Torr allows achieving an superhard state with a hardness of 44 GPa.Документ Structural Engineering of the Growth of Crystallites with a Predominant Orientation in Bilayer Multi-Period Vacuum arc Nitride Coatings(Sumy State University, 2018) Sobol, O. V.; Mygushchenko, R. P.; Postelnyk, A. A.; Onoprienko, E. V.; Syrenko, T. O.; Men'shikov, A. G.; Zvyagolskiy, A. V.The effect of the MeN (Me-Cr, Mo, Zr) layer composition in multiperiod vacuum-arc (TiAlSi) N / MeN coatings with a nanoscale layer thickness on the predominant orientation of crystallite growth in layer s and hardness was studied. It was found that phases with a cubic crystal lattice (structural type NaCl) in the layers of all types (TiAlSi)N/MeN coatings are formed, although for the MoN phase under equilibrium conditions a hexagonal crystal lattice is preferred. The interrelation between the structure of MeN and (TiAlSi)N layers is revealed, as well as the effect of the structural state on the coating hardness. Defining influence of the MeN layer on the formation of three structural states types was found: with a preferential crystallite growth with the texture axis [111]; with the texture axis [100]; the formation of a non-textured state. The highest hardness of 47.8 GPa was achieved in the (TiAlSi)N/ZrN multilayer coating with the texture axis [111].Документ The Influence of Layer Thickness and Deposition Conditions on Structural State of NbN/Cu Multilayer Coatings(Sumy State University, 2019) Sobol, O. V.; Andreev, A. A.; Meylekhov, A. A.; Postelnyk, A. A.; Stolbovoy, V. A.; Ryshchenko, I. M.; Sagaidashnikov, Yu. Ye.; Kraievska, Zh. V.The influence of the main physical and technological factors of structural engineering (layer thickness, nitrogen atmosphere pressure and bias potential) on the structural-phase state of the NbN/Cu coatings was studied. It was established that with an increase in the thickness of niobium nitride layers from 8 to 40 nm (in the NbN/Cu multilayer composition), the phase composition changes from the metastable NbN (cubic crystal lattice, NaCl structural type) to the equilibrium ε-NbN phase with a hexagonal crystal lattice. At low pressure PN = 7·10 – 4 Torr in thin layers (about 8 nm thick), regardless of the Ub, the NbN phase is formed. The reason for the stabilization of this phase can be the uniformity of the metallic fcc crystal lattice of the δ-NbN phase with the Cu crystal lattice. As the pressure increases from РN = 7·10 – 4 Torr to 3·10 – 3 Torr, a more equilibrium ε-NbN phase with a hexagonal crystal lattice is formed. An increase in the bias potential during deposition from – 50 V to – 200 V mainly affects the change in the preferred orientation of crystallite growth. In thin layers of the NbN phase (about 8 nm), a crystallite texture with the [100] axis is formed. In layers with a thickness of 40-120 nm, crystallites of the NbN phase are predominantly formed with a hexagonal (004) plane parallel to the growth plane. At the greatest layer thickness (more than 250 nm), the NbN phase crystallites are predominantly formed with a (110) hexagonal lattice plane parallel to the growth plane. The results obtained show great potential for structural engineering in niobium nitride when it is used as a constituent layer of the NbN/Cu multilayer periodic system.Документ Structural Engineering Multiperiod Coating ZrN/MoN(Sumy State University, 2016) Sobol, O. V.; Meylekhov, A. A.; Stolbovoy, V. A.; Postelnyk, A. A.Using the method of structural engineering by changing the thickness of the layers in a multiperiod ZrN/MoN system investigated the effect of the phase-texture state of the crystallites and their size on the hardness of the vacuum-arc coating. Is revealed a determining influence on the formation of ZrN layers preferential orientation growth [100] axis with a small layer thickness 7-20 nm (the deposition of 3 to 10 seconds). At high layer thickness determines the texture [311] crystallites are - Mo2N phase formed in the Mo-N layers. Pulsed high-voltage stimulation without changing the type of structural states for different layer thicknesses, leads to partial disorientation texture in thick layers. Hardness of coating with thick (80 nm) layers is 35-37 GPa. In small thickness layers pulse stimulation of atoms motility causes the formation of a planar structure with an average crystallite size of 4-9 nm in the layers, which is accompanied by increased hardness of up to 44 GPa.Документ The Influence of Layers Thickness on the Structure and Properties of Bilayer Multiperiod Coatings Based on Chromium Nitride and Nitrides of Transition Metals Ti and Mo(Sumy State University, 2018) Sobol, O. V.; Meylekhov, A. A.; Mygushchenko, R. P.; Postelnyk, A. A.; Tabaza, Taha A.; Al- Qawabah, Safwan M.; Gorban, V. F.; Stolbovoy, V. A.The influence of the layers thickness of bilayer multi-period coatings of the CrNx/MoNx and CrNx/TiNx systems on their phase-structural state, substructure, stress-strain state and mechanical properties was studied using methods of precision structural analysis in combination with computer simulation of implantation processes during particle deposition. It is established that a two-phase structure of CrN and-Mo2N phases of the structural type NaCl is formed in the multi-period coatings of the CrNx/MoNx system with a nanometer thickness of the layers. Because of the small difference in periods (less than 0.5 %) for Λ = 20 nm, the layers form a coherent interlayer interface. The use of small Ub – 20 V during deposition makes it possible to avoid significant mixing at interlayer (interphase) boundaries even at the smallest Λ = 10 nm. Nitride layers formed under conditions of vacuum arc deposition are under the action of compressive stresses. In the СrNх/TiNх system, because of the relatively large discrepancy between periods (more than 2.5 %), during the formation of the same structural components in the layers (CrN and TiN phases of the structural type NaCl), the epitaxial growth with period adjusting does not occur, even for the smallest Λ = 10 nm. The action of the deformation factor at the interphase boundary allows achieving an ultrahard state (with a hardness of about 50 GPa), which causes a relatively low friction coefficient. The obtained results on the formation of phase-structural states with the nanoscale thickness of layers of multi-period nitride coatings are explained from the position of minimization of surface energy and deformation energy.Документ А Computer Simulation of Radiation-Induced Structural Changes and Properties of Multiperiod ZrNₓ/MoNₓ System(Sumy State University, 2017) Sobol, O. V.; Meylekhov, A. A.; Bochulia, T. V.; Stolbovoy, V. A.; Gorban, V. F.; Postelnyk, A. A.; Shevchenko, S. M.; Yanchev, A. V.Influence of the period value Λ (at different negative potential Ub that supplied during deposition) on phase composition, structure, stress-strain state and hardness of multiperiod coatings ZrNₓ/MoNₓ is investigated by using complex methods of validation structural state at combined with microindentation. Formation in layers ZrNx and MoNx the phases with cubic lattice and preferred orientation of crystallites with axis [100] is established. Stress-strain state of compression with increasing Ub is amplified and reaches maximum value (– 6.7 GPa) at Λ = 20 nm and Ub – 110 V. Hardness of coating increases with decreasing Λ from 300 to 20 nm. Coatings that obtained with Λ = 20 nm and Ub – 110 V have the highest hardness 44 GPa. Relaxation of structural compressive stresses and decreasing hardness is happening at smaller Λ and larger Ub – 110 V (as a result of radiation-stimulated forming defect and mixing). Data of computer modeling of defectiveness at atomic level at bombardment of ions that accelerated in field Ub are used to explain the results.Документ Structure and Properties of Vacuum Arc Single-Layer and Multiperiod Two-Layer Nitride Coatings Based on Ti(Al):Si Layers(Sumy State University, 2017) Beresnev, V. M.; Sobol, O. V.; Pogrebnjak, A. D.; Lytovchenko, S. V.; Stolbovoy, V. A.; Srebniuk, P. A.; Novikov, V. Ju.; Doshchechkina, I. V.; Meylehov, A. A.; Postelnyk, A. A.; Nyemchenko, U. S.; Mazylin, B. A.; Kruhlova, V. V.The paper provides an analysis of impact of deposition conditions on structural and phase state and thermal stability of vacuum arc coatings based on Ti(Al):Si layers. We studied single-phase single-layer coatings, and multiperiod bilayer coatings with second phase nitride interlayers of one of the following three metals: Mo, Cr or Zr. It was established that hexagonal and cubic lattices may form in the coatings when transition to the cubic lattice occurs with Al content of about 25 at. %. Presence of second nanoscale (7-8 nm) layers in bilayer multiperiod compositions, which consist of one nitride from CrNx, MoNx or ZrNx group, does not change the type of lattice in [Ti(Al):Si]Nx layers. Also, an fcc lattice with a strong or weak texture [111] forms in CrNx and ZrNx layers, while crystallites with hexagonal lattice form in MoNx layers. High-temperature annealing at 700 °С during 40 minutes leads to a significant (by 23 % or up to H 47.56 GPa) increase in microhardness of coating of the [Ti(Al)]Nx/ZrNy system due to formation of a nano-size structure with an average size of crystallites of 3.6 nm in [Ti(Al)]Nx layers, and 6.3 nm in ZrNx layers.Документ Influence of the magnitude of the bias potential and thickness of the layers on the structure, substructure, stress-deformed state and mechanical (TiMo)N/(TiSi)N coatingsl characteristics of vacuum-arc multi-layered(2020) Sobol, O. V.; Postelnyk, H. O.; Meylekhov, A. A.; Subbotina, V. V.; Stolbovoy, V. A.; Dolomanov, A. V.; Kolesnikov, D. A.; Kovaleva, M. G.; Sukhorukova, Yu. V.Layers based on titanium nitride doped with molybdenum and silicon were used to create a multilayer composite. In this case, the mismatch between the lattice periods of (TiMo)N and (TiSi)N layers was about 1%. It was found that in the (TiMo)N/(TiSi)N multilayer composite, such a mismatch of the periods in the constituent layers does not change the single-phase state of the composite even at relatively large layer thicknesses (about 350 nm). The creation of a (TiMo)N/(TiSi)N composite with a nanometer layer thickness allows one to reduce the magnitude of macrostresses (a large value of which is characteristic of single-layer (TiMo)N coatings) and change the substructural characteristics in a wide range of values. It has been established that the use of multi-element (TiMo)N and (TiSi)N layers in a multilayer coating design allows one to achieve a high-hard state with high adhesive strength and good tribological characteristics. The highest properties (hardness – 34.8 GPa and adhesive strength 166.09 N) were achieved in coatings obtained at Ub = -200 V and a layer thickness of 80 nm, which are characterized by compression macrostresses of 7.85 GPa and microstrains 0.75%.Документ Structure and corrosion resistance of vacuum-arc multi-period CrN/Cu, ZrN/Cu and NbN/Cu coatings(2020) Postelnyk, H. O.; Sobol, O. V.; Stolbovoy, V. A.; Serdiuk, I. V.; Chocholaty, O.The structure and properties of vacuum-arc multi-period composite coatings of the MeN/Cu system (where Me is Cr, Zr, and Nb) are studied. It was found that at the smallest nanolayer thickness (about 8…10 nm) of composites in the layers of all systems, only a phase with an fcc lattice is formed, without a pronounced texture in the nitride layers. For ZrN and CrN, the phases with an fcc lattice are equilibrium, and for NbN, they are nonequilibrium. An increase in the thickness of nitride layers leads to the appearance of a texture in ZrN/Cu and CrN/Cu systems and the formation of an equilibrium ε-NbN phase in the layers of the NbN/Cu system. Tests for corrosion resistance in the environment of the formation of chloride ions showed that the coatings are anodic reaction. The best corrosion properties were obtained for coatings with the smallest layer thickness (about 8…10 nm).Документ The use of negative bias potential for structural engineering of vacuum-arc nitride coatings based on high-entropy alloys(2019) Sobol, O. V.; Andreev, A. A.; Gorban, V. F.; Postelnyk, H. O.; Stolbovoy, V. A.; Zvyagolsky, A. V.; Dolomanov, A. V.; Kraievska, Zh. V.The effect of negative bias potential (Ub = -40, -110, and -200 V) during the deposition of multi-element coatings on their composition, structure and mechanical properties was studied. It was established that during the transition from a multi-element alloy to a nitride, a single-phase state possible to form on its basis (based on the fcc metal lattice, structural type NaCl). In this case, the composition (FeCoNiCuAlCrV)N of coatings with increasing Ub is depleted by the element with the lowest enthalpy of formation of nitride (Cu). In (AlCrTiNbSi)N and (AlCrTiZrNbV)N coatings, the content of low-mass elements (Si and Al) decreases with increasing Ub. In (TiZrHfVNb)N coatings of strong nitride-forming elements with increasing Ub to 200 V, the composition practically does not change. The structure of such coatings is characterized by the presence of a texture with the [111] axis. The presence of weak nitride-forming elements in (FeCoNiCuAlCrV)N coatings leads to the formation of texture [110] for large Ub = 110…200 V. In such coatings, the hardness does not exceed 35 GPa. It is shown that to achieve high hardness at high Ub it is necessary to increase the content in the high-entropy alloy of elements with high nitride-forming ability. In this case, in (TiZrHfVNb)N coatings (made of strong nitride-forming elements with a large mass) at Ub = 200 V, the hardness exceeds 45 GPa.