Різання та інструменти в технологічних системах

Постійне посилання на розділhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/62923

У збірнику публікуються наукові статті, у яких висвітлюються актуальні питання в області механічної обробки сучасних матеріалів із застосуванням високопродуктивних технологій, нових методів та вимірювальних приладів для контролю якості оброблених поверхонь і високоефективних різальних інструментів. Висвітлюються аспекти оптимізації й математичного моделювання на різних етапах технологічного процесу.

Рік заснування: 1966. Періодичність: 2 рази на рік. ISSN 2078-7405 (Print)

Новини

Збірник «Різання та інструменти в технологічних системах» включено до Переліку наукових фахових видань України з технічних наук до категорії «Б» згідно Наказу МОН України №409 від 17.03.2020 р.

Переглянути

Результати пошуку

Зараз показуємо 1 - 4 з 4

Roughness investigation of single and double cutting marks on face milled surface
(Національний технічний університет "Харківський політехнічний інститут", 2023) Nagy, Antal; Kundrak, Janos
In machining with defined cutting edge tools, in some rotational tool processes (e.g. face milling) the tool edge may scratch the surface of the workpiece one more time, depending on the cutting conditions, during one revolution of the tool. As a result, the topographies with single or double cutting marks will be different from each other. The deviation, depending on its size, can also affect the functional performance (e.g. friction conditions) of the operating surfaces. In this article, face-milled topographies created with a symmetrical setting and with single or double milling marks are compared according to the magnitude of the roughness and the degree and nature of the inhomogeneity.
Investigation of face milled surface topography on C45 workpiece assuming movement at 30° and 60° to feed direction
(Національний технічний університет "Харківський політехнічний інститут", 2023) Nagy, Antal; Kundrak, Janos
When surfaces with anisotropic texture are moved in different directions related to their assembled counterpart during operation, the friction conditions change, as they are determined by the lay of the topographies. In the article, contributing to the exploration of this characteristic, we analyze the inhomogeneity of the topography on a face milled plane surface with a symmetrical setting in sections at an angle of 30° or 60° to the feed direction. Roughness profiles are recorded at 13 pointslocated equidistantly from each other in each measurement plane, and the degree and distribution of the roughness deviations are determined on the surface.
Analyzing the effect of the tool pass number and the direction of sliding burnishing on surface roughness
(Національний технічний університет "Харківський політехнічний інститут", 2022) Nagy, Antal; Varga, Gyula
Nowadays, the concern of environmental protection is becoming more and more important in production as well. They often contribute to this by reducing or eliminating the amount of coolants and lubricants, or by using alternative machining methods. One of them is burnishing, which makes a positive effect on surface integrity, while reduces the environmental load. In this paper we examined the change in surface roughness achieved by burnishing after turning on a corrosion-resistant steel workpiece, where the number of burnishing passes and burnishing direction were changed. The results showed increased smoothness, bearing capacity and dimensional stability by increasing the number of passes from 1 to 2, however, the 3 times repetition did not show any additional favorable improvement on the surfaces. In case of the forward-backward-forward burnishing directions, further chipping occurred, in other cases the effect of the directions was negligible on the amplitude roughness parameters, but considerable on the parameters characterizing the roughness peak. The greatest improvement was achieved with the backward-forward settings.
Investigation of the effect of areal roughness measurement length on face milled surface topographies
(Національний технічний університет "Харківський політехнічний інститут", 2021) Nagy, Antal
Surface roughness is of great importance in the manufacturing industry, as it affects surfaces’ tribological properties (wear, friction, lubrication, etc.), corrosion resistance, fatigue strength and appearance. Areal roughness measurement, which provides a more comprehensive characterization of surfaces, is becoming increasingly popular, but systematic studies are still lacking, so measurements are often analyzed differently. In this paper, the effect of the measurement length is analyzed in the main measurement direction on areal roughness of face milled surface topographies, which were measured with a confocal chromatic sensor.