Кафедра "Матеріалознавство"

Постійне посилання колекціїhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/6927

Офіційний сайт кафедри http://web.kpi.kharkov.ua/mtrlvd

Від 2007 року кафедра має назву "Матеріалознавство", первісна назва – "Металознавство та термічна обробка металів".

Кафедра "Металознавство та термічна обробка металів" створена у 1932 році. Першим її очільником став доктор технічних наук, професор Олександр Володимирович Терещенко.

Кафедра являє собою одну із найстаріших в політехнічному інституті з підготовки інженерів-технологів-дослідників. Своїми науковими дослідженнями. з початку своєї діяльності, кафедра сприяла розвитку та удосконаленню технологій термічної та хіміко-термічної обробки деталей на підприємствах України».

Кафедра входить до складу Навчально-наукового інституту механічної інженерії і транспорту Національного технічного університету "Харківський політехнічний інститут".

У складі науково-педагогічного колективу кафедри працюють: 1 доктор технічних наук, 9 кандидатів технічних наук, 3 кандидата фізико-математичних наук, 1 доктор філософії; 1 співробітник має звання професора, 8 – доцента, 1 – старшого наукового співробітника.

Переглянути

Фільтри

2015 - 201922020 - 20242

Налаштування

Містить файли: ТакКлючові слова: search.filters.subject.vacuum-arc coatings

Результати пошуку

Зараз показуємо 1 - 4 з 4
  • Ескіз
    Документ
    Design of experiments of PVD coatings tin
    (Сумський державний університет, 2024) Pinchuk, N. V.
  • Ескіз
    Документ
    Structure, Substructure, Hardness and Adhesion Strength of Multiperiod Composite Coatings MoN / CrN
    (Sumy State University, 2015) Grankin, S. S.; Beresnev, V. M.; Sobol, O. V.; Stolbovoy, V. A.; Novikov, V. Yu.; Lytovchenko, S. V.; Nyemchenko, U. S.; Meylekhov, A. A.; Kovaleva, M. G.; Postelnyk, A. A.; Toryanik, I. N.
    A comprehensive study of the influence of the thickness of the layers, Us and PN on the structural engineering to obtain high mechanical properties in multilayer composite MoN / CrN vacuum-arc coatings has been conducted by means of scanning electron microscopy with energy analysis, X-ray diffraction studies microindentation and scratch testing methods. It has been determined that in the studied Torr, the content of nitrogen in the coatings varies from 6.3 to 33 at. %, which leads even at the greatest nitrogen content to the formation of lower phase by nitrogen and isostructural CrN with the vacant sites in the nitrogen sublattice. The increase of thickness of the layers applied on the substrate in a stationary state promotes the increase of nitrogen content. Along with this, the lowest microdeformation and the average size of crystallites are formed at Ub = – 300 V, which defines the achievement of greater hardness of 35 GPa and high adhesion strength, which resists the destruction, Lc5 = 187.6 N.
  • Ескіз
    Документ
    Influence of the magnitude of the bias potential and thickness of the layers on the structure, substructure, stress-deformed state and mechanical (TiMo)N/(TiSi)N coatingsl characteristics of vacuum-arc multi-layered
    (2020) Sobol, O. V.; Postelnyk, H. O.; Meylekhov, A. A.; Subbotina, V. V.; Stolbovoy, V. A.; Dolomanov, A. V.; Kolesnikov, D. A.; Kovaleva, M. G.; Sukhorukova, Yu. V.
    Layers based on titanium nitride doped with molybdenum and silicon were used to create a multilayer composite. In this case, the mismatch between the lattice periods of (TiMo)N and (TiSi)N layers was about 1%. It was found that in the (TiMo)N/(TiSi)N multilayer composite, such a mismatch of the periods in the constituent layers does not change the single-phase state of the composite even at relatively large layer thicknesses (about 350 nm). The creation of a (TiMo)N/(TiSi)N composite with a nanometer layer thickness allows one to reduce the magnitude of macrostresses (a large value of which is characteristic of single-layer (TiMo)N coatings) and change the substructural characteristics in a wide range of values. It has been established that the use of multi-element (TiMo)N and (TiSi)N layers in a multilayer coating design allows one to achieve a high-hard state with high adhesive strength and good tribological characteristics. The highest properties (hardness – 34.8 GPa and adhesive strength 166.09 N) were achieved in coatings obtained at Ub = -200 V and a layer thickness of 80 nm, which are characterized by compression macrostresses of 7.85 GPa and microstrains 0.75%.
  • Ескіз
    Документ
    Structural engineering of NbN/Cu multilayer coatings by changing the thickness of the layers and the magnitude of the bias potential during deposition
    (2019) Sobol, O. V.; Andreev, A. A.; Stolbovoy, V. A.; Kolesnikov, D. A.; Kovaleva, M. G.; Meylekhov, A. A.; Postelnyk, H. O.; Dolomanov, A. V. ; Sagaidashnikov, Yu. Ye.; Kraievska, Zh. V.
    To determine the patterns of structural engineering of vacuum-arc coatings based on niobium nitride in the NbN/Cu multilayer composition, the effect of layer thickness and bias potential on the structural-phase state and physico-mechanical characteristics of vacuum-arc coatings was studied. It was found that the metastable δ-NbN phase (cubic crystal lattice, structural type NaCl) is formed in thin layers (about 8 nm thick) regardless of Ub. With a greater thickness of the layers of niobium nitride (in the multilayer NbN/Cu composition), the phase composition changes from metastable δ-NbN to the equilibrium ε-NbN phase with a hexagonal crystal lattice. An increase in the bias potential during deposition from -50 to -200 V mainly affects the change in the preferential orientation of crys-tallite growth. The highest hardness (28.2 GРa) and adhesive resistance is achieved in coatings obtained at Ub = -200 V with the smallest layer thickness. The highest hardness corresponds to the structurally deformed state in which the crystallite texture is formed with the [100] axis perpendicular to the growth surface, as well as a large microstrain (1.5%) in crystallites.