Кафедра "Електричний транспорт та тепловозобудування"
Постійне посилання колекціїhttps://repository.kpi.kharkov.ua/handle/KhPI-Press/5269
Офіційний сайт кафедри http://web.kpi.kharkov.ua/ett
Від 2000 року кафедра має назву "Електричний транспорт та тепловозобудування", попередня назва – кафедра "Локомотивобудування" (від 1956), первісна назва – кафедра "Паровозобудування".
Кафедра "Паровозобудування" була заснована у 1893 році. Засновником напрямку навчання інженерів-паровозобудівників є професор Петро Матвійович Мухачов.
Кафедра входить до складу Навчально-наукового інституту енергетики, електроніки та електромеханіки. Кафедрою здійснено понад 100 випусків спеціалістів – локомотивобудівників.
У складі науково-педагогічного колективу кафедри працюють: 3 доктора технічних наук, 5 кандидатів технічних наук; 3 співробітника мають звання професора, 3 – доцента, 1 – старшого наукового співробітника.
Переглянути
3 результатів
Результати пошуку
Документ Analysis of operating modes of single-phase current source rectifier with rectangular-stepped pulse-width modulation(Технологический центр, 2018) Krasnov, Oleksii; Liubarskyi, Borys; Bozhko, Vladimir; Petrenko, Оleksandr; Dubinina, Oksana; Nuriiev, RamilThe operating modes of the single-phase active current-source rectifier in the case of rectangular-stepped pulse-width modulation and load in the form of DC traction motor are investigated. The single-phase bridge rectifier circuit with a discharge diode is considered. The mathematical model of the rectifier is developed and the main ratios for pulse-width modulation with rectangular-stepped modulating signal are determined. On the computer model, electromagnetic processes at three modulation frequencies (900, 1,200, 1,800 Hz) are studied. The features of the effect of the modulation depth and frequency on the rectifier power factor and the total harmonic voltage and current distortion in the mains supply are determined. The DC motor for today remains the main type of the traction motor of the 25 kV, 50 Hz AC mainline electric locomotives of alternating current in Ukraine and in some other countries. To power such motors, diode or thyristor rectifiers are used. At the same time, it is known that converters on fully controlled semiconductor devices provide higher power efficiency. The studies allow determining what values of modulation frequency and depth provide a high power factor (more than 0.9) and minimum total harmonic voltage and current distortion distortions in the mains supply. This allows finding rational approaches to the selection of power circuits and control algorithms for active converters in the traction electric drive of electric locomotives. The efficiency of increasing the power factor and reducing the total harmonic voltage and current distortion can be achieved, first of all, by reducing the power consumption for traction of trains. According to the set of selected comparison criteria, the active current-source rectifier with a modulation frequency of 1,200 Hz is the most suitable for implementation in the traction electric drive of the electric locomotive. Provision of high power characteristics in a wide range of traction loads can be achieved in the multi-zone circuit of such a converter.Документ Optimization of thermal modes and cooling systems of the induction traction engines of trams(Технологический центр, 2017) Liubarskyi, Borys; Petrenko, Оleksandr; Iakunin, Dmytro; Dubinina, OksanaWe developed a procedure for the optimization of thermal modes and parameters of the cooling system of induction traction engines of tram carriages. The procedure includes the following basic steps. The optimization of operating modes of an induction traction drive by the criterion of effectiveness of its work under different modes. The optimization of motion modes of a tram carriage along a track section with the assigned motion schedule and profile based on the curves of the motion of a tram carriage, optimal by the criterion of energy consumption, using the method of Hamilton-Jacobi-Bellman. The optimization of parameters of the cooling fan of traction engines by the criterion of efficiency of a cooling system using the Weyl method by the generalized golden section. It is proposed to conduct determining of operating modes of a traction drive in advance based on the solution to the problem of conditional optimization of its modes. In order to determine the optimal operating modes of a traction drive, we selected a combined method: global search is executed by genetic algorithm with a one-point crossover and by selection on the principle of roulette. At the final stage of an optimization procedure, optimum refining is carried out using the Nelder-Mead method. When a tram carriage moved along a track section, we defined the following. We determined the optimal modes of motion of the tram carriage T-3 VPA with induction traction engines for a track section with the assigned motion schedule. It was found that, compared with the basic design, efficiency of the cooling system increased by 27.6 %, which corresponds to a reduction in the proposed criterion of efficiency. Based on the results of modeling a traction engine with an optimal fan, it was established that the largest overheating is observed in the frontal part of the stator winding. The temperature is 139.6 °C at second 3363 from starting the motion and it does not exceed a permissible value of 140 °C.Документ Procedure for modeling dynamic processes of the electromechanical shock absorber in a subway car(Технологический центр, 2019) Liubarskyi, Borys; Lukashova, Natalia; Petrenko, Oleksandr; Yeritsyan, Bagish; Kovalchuk, Yuliia; Overianova, LiliiaA procedure has been devised for modeling the dynamic pro-cesses in the proposed structure of an electromechanical shock absorber. Such shock absorbers can recuperate a part of the energy of oscillations into electrical energy allowing the subsequent possibility to use it by rolling stock. The procedure is based on solving the Lagrange equation for the electromechanical system. The model’s features are as follows. The model takes the form of a Cauchy problem, thereby making it possible to use it when simulating the processes of shock absorber operation. Two generalized coordinates have been selected (the charge and displacement of the armature). The components of the Lagrange equation have been identified. Based on the results from magnetic field calculation and subsequent regression analysis, we have derived polynomial dependences of flux linkage derivatives for the current and linear displacement of an armature, which make it possible to identify a generalized mathematical model of the electromechanical shock absorber. The magnetic field calculations, performed by using a finite-element method, have allowed us to derive a digital model of the magnetic field of an electromechanical shock absorber. To obtain its continuous model, a regression analysis of discrete field models has been conducted. When choosing a structure for the approximating model, a possibility to analytically differentiate partial derivatives for all coordinates has been retained. Based on the results from modeling free oscillations, it was established that the maximum module value of current is 0.234 A, voltage – 52.9 V. The process of full damping of oscillations takes about 3 seconds over 4 cycles. Compared to the basic design, the amplitude of armature oscillations and its velocity dropped from 13 to 85 % over the first three cycles, indicating a greater efficiency of electromechanical shock absorber operation in comparison with a hydraulic one. The recuperated energy amounted to 3.3 J, and the scattered energy – 11.5 J.